Dell PowerEdge T710 User Manual

148 Installing System Components
Installing the Control Panel Assembly
WARNING: Only trained service technicians are authorized to remove the system
cover and access any of the components inside the system. Before you begin this
procedure, review the safety instructions that came with the system.
1 Connect the control panel cable to the control panel board. See
Figure 3-28.
2 Insert the control panel assembly, cable first, into the chassis. See
Figure 3-28.
Gently work the control panel assembly into the chassis until it is fully
seated against the front of the chassis.
3 Replace the Torx screw on the top side of the chassis. See Figure 3-28.
4 Install the outer cover on the top side of the chassis.
a Insert the cover tabs into the slots in the top side of the chassis. See
Figure 3-28.
b Hook the top edge of the cover over the top edge of the chassis. See
Figure 3-28.
c Slide the cover towards the front of the system. See Figure 3-28.
d Replace the two hex-head Phillips screws on the back of the system to
secure the cover to the chassis.
5 Replace the Torx screw on the front of the system to secure the control
panel assembly to the chassis. See Figure 3-28.
6 Connect the control panel cable to CTRL_PNL connector on the system
board. See Figure 6-1 for the connector location.
7 Close the system. See "Closing the System" on page 86.
8 Place the system upright and on its feet on a flat, stable surface.
9 Rotate the system feet outward.
10 Reattach any peripherals, then connect the system to the electrical outlet.
11 Turn on the system and attached peripherals.
book.book Page 148 Monday, June 15, 2009 11:33 AM

Dell PowerEdge T710 Specifications

General

Tcase	76 °C
Bus type	QPI
Stepping	D0
FSB Parity	No
Processor code	SLBF8
Processor cache	4 MB
Processor cores	4
Processor model	E5506
System bus rate	4.8 GT/s
Processor series	Intel Xeon 5500 Series
Processor socket	Socket B (LGA 1366)
Processor codename	Nehalem EP
Motherboard chipset	Intel® 5520
Number of QPI links	2
Processor frequency	2.13 GHz
Processor cache type	Smart Cache
Processor lithography	45 nm
Processor system type	DP
Processor manufacturer	Intel
Processor package size	42.5 x 45 mm
Processor front side bus	- MHz
Processor operating modes	64-bit
ECC supported by processor	Yes
Thermal Design Power (TDP)	80 W
Compatible processor series	Intel® Xeon®
Number of processors installed	1
CPU multiplier (bus/core ratio)	16
Memory types supported by processor	DDR3-SDRAM
Memory channels supported by processor	Triple
Memory clock speeds supported by processor	800 MHz
Memory bandwidth supported by processor (max)	19.2 GB/s
Maximum internal memory supported by processor	144 GB
HDD size	3.5 \
HDD speed	15000 RPM
HDD interface	Serial Attached SCSI (SAS)
Optical drive type	DVD-ROM
Total storage capacity	300 GB
Maximum storage capacity	- TB
Number of HDDs supported	6
Graphics card	G200
Graphics card family	Matrox
Memory slots	18x DIMM
Internal memory	4 GB
Memory clock speed	1333 MHz
Maximum internal memory	192 GB
Memory layout (slots x size)	2 x 2 GB
Networking features	Gigabit Ethernet
PS/2 ports quantity	0
USB 2.0 ports quantity	8
PCI Express x8 slots	5
Power supply	1100 W
Number of power supply units	-
Compatible operating systems	Windows Small Business Server 2011 Windows Small Business Server 2008 Windows Server 2008 SP2, x86/x64 (x64 includes Hyper-V) Windows Server 2008 R2 SP1, x64 (includes Hyper-V v2) Windows HPC Server 2008 Novell SUSE Linux Enterprise Server Red Hat Enterprise Linux
Sustainability certificates	ENERGY STAR
Compliance industry standards	IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Chassis type	Tower (5U)
Processor ARK ID	37096

Weight and Dimensions

Depth	731.8 mm
Width	217.9 mm
Height	466.3 mm
Weight	35300 g