EasyManuals Logo
Home>Denon>Receiver>AVR-X2000

Denon AVR-X2000 User Manual

Denon AVR-X2000
220 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #129 background imageLoading...
Page #129 background image
129
Appendix
TipsPlaybackConnections
Contents
Front panel Display Rear panel IndexRemote
Settings
2 Reference Level Oset
Audyssey Dynamic EQ® is referenced to the standard film mix level. It
makes adjustments to maintain the reference response and surround
envelopment when the volume is turned down from 0 dB. However,
film reference level is not always used in music or other non-film
content. Dynamic EQ Reference Level Oset provides three osets
from the film level reference (5 dB, 10 dB, and 15 dB) that can be
selected when the mix level of the content is not within the standard.
Recommended setting levels for content are shown below.
0dB (Film Ref) (Default) : Optimized for content such as movies.
5dB : Select this setting for content that has a very wide dynamic
range, such as classical music.
10dB : Select this setting for jazz or other music that has a wider
dynamic range. This setting should also be selected for TV
content as that is usually mixed at 10 dB below film reference.
15dB : Select this setting for pop/rock music or other program material
that is mixed at very high listening levels and has a compressed
dynamic range.
%
•Setting is enabled when “Dynamic EQ” (vpage128) is “On”.
2 Dynamic Volume
Solves the problem of large variations in volume level between TV,
movies and other content (between quiet passages and loud passages,
etc.) by automatically adjusting to the user’s preferred volume setting.
Heavy : Most adjustment to softest and loudest sounds.
Medium : Medium adjustment to loudest and softest sound.
Light : Least adjustment to loudest and softest sounds.
O (Default) : Do not use “Dynamic Volume”.
%
•If “Dynamic Volume” is set to “Yes” in “Audyssey® Setup” (vpage141),
the setting is automatically changed to “Medium”.

Table of Contents

Other manuals for Denon AVR-X2000

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-X2000 and is the answer not in the manual?

Denon AVR-X2000 Specifications

General IconGeneral
Receiver type-
Frequency range10 - 100000 Hz
Output impedance16 Ω
Input sensitivity200 mV
Audio output channels7.1 channels
Signal-to-Noise Ratio (SNR)100 dB
Power output per channel (1KHz@6 Ohm)125 W
Power output per channel (20-20KHz@8 Ohm)95 W
HDMI in7
AC (power) inYes
Audio (L/R) in4
Composite video in2
Component video (YPbPr/YCbCr) in1
Connectivity technologyWired
Speakers connectivity typeBanana connector
Audio formats supportedAAC, FLAC, MP3, WAV, WMA
Image formats supportedJPG
Wi-FiNo
RDS featuresPTY, TP
FM band range87.5 - 108 MHz
Supported radio bandsFM
Internet radio services supportedSpotify, vTuner
Supported video modes1080i, 1080p, 480p, 576p, 720p
DisplayVFL
Color depth24 bit
Aspect ratio4:3, 16:9
Product colorBlack
Audio decodersDolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS, DTS-ES, DTS-HD, DTS-HD Master Audio
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Apple docking compatibilityNot supported
AC input voltage230 V
AC input frequency50 - 60 Hz
Power consumption (standby)0.1 W
Power consumption (typical)500 W
Weight and Dimensions IconWeight and Dimensions
Depth330 mm
Width434 mm
Height167 mm
Weight9500 g

Related product manuals