34 35
Part # 8533-073-001 3/22 Part # 8533-073-001 3/22
#4 Warm Water Price: The next step in the pricing program is to set the additional price for Warm
water usage. The display will blink rst “CH P” indicating cold/hot water mix price and then “00.00”.
To change the value, use the Hot temperature button to decrease and the Warm temperature button
to increase. The value will change in 1¢ steps. The range of values is from $00.00 to $99.99.
NOTE: To not use this feature, set the price to “00.00”.
When the desired price is displayed, push the Start button once to store the new value and a second
time to move to the next Coin/Price programming step. To exit the Coin/Price programming mode,
push the Cold temperature button for 5 seconds.
#5 Hot Water Price: The next step in the pricing program is to set the additional price for Hot water
usage. The display will blink rst “H P” indicating hot water price and then “00.00”. To change the
value, use the Hot temperature button to decrease and the Warm temperature button to increase.
The value will change in 1¢ steps. The range of values is from $00.00 to $99.99.
NOTE: To not use this feature, set the price to “00.00”.
When the desired price is displayed, push the Start button once to store the new value and a second
time to move to the next Coin/Price programming step. To exit the Coin/Price programming mode,
push the Cold temperature button for 5 seconds. The Coin/Price programming mode will automatically
exit and return to the Idle mode if no buttons are pushed for one minute.
#6 Plus Cycle Price: The next step in the programming sequence is the Plus Cycle feature. The Plus
Cycle adds three (3) minutes of wash time to the wash bath only. The controller can be programmed
to charge a fee for this or the feature can be turned o. The default setting is o ($0.00).
The display will blink rst a “PC P” indicating Plus Cycle price and then price (back and forth). To
change the value, use the Hot temperature button to decrease and the Warm temperature button to
increase. The value will change in 1¢ steps. The range of values is from $00.01 to $99.99. When the
desired price is displayed, push the Start button once to store the new value and a second time to
move to the next Coin/Price programming step. To exit the Coin/Price programming mode, push the
Cold temperature button for 5 seconds.
#7 Decimal Point: The next step in the programming sequence is the Decimal Point. The display will
blink“dP” and Default value is ON. The value “on” for enable or “o” for disable. Once a pushbutton
is pressed, the display will stop blinking and show the decimal point value. The decimal point value
will display and change with the Hot and Warm buttons. When desired value is reached press Start
button.
Wash Cycle Programming
To change a feature of the wash cycle, push and hold the Hot temperature button and then push the
programming pushbutton on the controller. The Washer mush be in the Idle mode to enter the Wash Cycle
Programming mode. When entering the cycle programming mode the Bleach LED will start to blink and
continue to blink as long as you are in the Cycle Programming mode. The display will show “C 0”. This is
the default cycle number.
NOTE: The washer can be returned to the factory default settings by holding the right Warm button
and then pressing the left Warm button. The display must show “C 0” to do this. When the cycle
default values are loaded, the washer will automatically exit the programming mode.
NOTE: The Wash Cycle programming mode will automatically exit and return to the Idle mode if no
buttons are pushed for one minute.
To change the washer cycle, push the Hot temperature button once. The display will change to “C 1”,
indicating cycle one is selected. The temperature buttons are used to make changes to the program. In
the program mode, these buttons will do as displayed in drawing below.
When the display shows “C 1”, push Enter. The display will show “b “ and the PreWash mode light will
blink. Use the Up/Down buttons to move to the bath that will be changed. As Up/Down buttons are
pushed, the next bath mode light turns on.
When the Up button is pushed, the lit bath mode changes from Prewash to Wash. With each additional
push of the Up button, the lit bath mode changes from left to right: Prewash, Wash, Rinse and Final Rinse.
As there are two possible Rinse bathes, for Rinse 1 the Rinse LED and the display changes to “b” in the
left digit and “r1” in the two right hand digits. For Rinse2, the display changes to “b” in the left digit and
“r2” in the two right hand digits. Note that the Spin light is not used. When the Down button is pushed,
the lit bath mode changes from Prewash to Final Rinse, etc.. There is a wrap around feature on the display
in both directions.When the desired bath mode light is on, push Start.
Bath Cycle Time
The selected bath LED begins to blink. The display shows the letters “ct” in the left two digits and the
bath cycle time in the right two digits. Again the up/down buttons change this value. The range is shown
below. If zero time is entered, then the bath will be skipped and the program will return to the bath
selection. When the desired cycle time is selected, push Start.
Bath Water Temperature
The display shows the letter “t” in the left digit and the letters “CC” appear in the right two digits. This is
the bath water temperature. The selection choices are shown below but for the coin washer the value is
defaulted to CC. As it is not selectable with a coin washer, the owner pushes Start to continue.
Bath Water Level
The display shows the letter “L” in the left digit and the letters “LO” appear in the right two digits. This is
the bath water level. The selection choices are shown below but for the coin washer the value is defaulted
to LO. As it is not selectable with a coin washer, the owner pushes Start to continue.
Bath Delay Fill
The display shows the letters “dF” in the left two digits and the letter “t” appears in the right digit. This
is the bath delay ll. The selections are “t” for decrementing bath time during the ll or “d” for delay the
bath time until water level is reached. When the desired selection is made, push Start.
Bath Spin
The display shows the letter “S” in the left digit and the bath spin time in the right two digits. Again the
up/down buttons change this value. The range is shown below. When the desired spin time is selected,
push Start. The display shows the letters “IS” in the left two digits and the injection selection appears in
the right digit. For the coin washer the default value is “0” and cannot be changed. Push COLD.
The display will show “b” and the bath LED lights will stop blinking. Again use the up/down buttons change
the bath selection. To exit the programming mode, push and hold COLD until price is displayed. The cycle
will be stored when exiting the programming mode.
To Next Page
Loading...
Need help?
General
