21
When option [4] is selected, a high input (+12 V) will force
the panel to pick up the phone line and await
communications from downloading. This option is used for
on-site downloading or for use with the LINKS 1000 Cellular
Alarm Transmitter.
See Auxiliary Input Terminal in the “Terminal Connections”
section on page 4 for details on the Auxiliary Input. When
option [3] is selected, a momentary key closure between the
Auxiliary Input and the Positive Auxiliary Power Supply will
alternately arm and disarm the system. The reporting codes
for the Auxiliary Input (sections [9] and [10]) can be used as
opening and closing codes for key arming but will only be
transmitted with side A openings and closings.
2nd Digit Programmable Output
See programmable Output Terminal in the “Terminal
Connections” section on page 4 for details on connecting
the “PGM OUT” terminal.
[0] LINKS Support Output. Select this option if a LINKS
1000 Cellular Alarm Transmitter is to be used with the
panel. The PGM output terminal is used to control the
LINKS 1000. The PGM output will activate the LINKS
1000 after an unsuccessful communication attempt on
the regular phone line.
[1] Ground Start Pulse provides a 2 second ground start
pulse before dialing begins to obtain the dial tone on
ground start telephone equipment.
[2] Utility Output ([
Q], [7]) no access code
[3] Utility Output ([Q], [7]) any access code
[4] Utility Output ([
Q], [7]) Group A access code
[5] Utility Output ([
Q], [7]) Group B access code
These options change the “PGM OUT” terminal to different
options used with the keypad utility output [
Q][7] command.
See Utility Output Command in the “Keypad Command”
section.
[6] Keypad Buzzer Follow Mode. With this option the “PGM
OUT” terminal switches to ground as long as the keypad
buzzer is on.
[7] System Status (Arm/Disarm) Output. With this option
the “PGM OUT” terminal switches to ground when the
panel is armed. The switch is open when the panel is
disarmed.
[8] Strobe Output (latched alarm output). With this option
the “PGM OUT” terminal switches to ground after an
alarm and remains switched on until the system is
disarmed.
[9] Failure to Communicate Output.
With this option the
“PGM OUT” terminal switches to ground if the system
fails to communicate with the monitoring station after 8
attempts. The output stays switched to ground until a
successful communication takes place or until trouble #5
is cleared from the keypad. This option may be used to
tie two systems together. One system can then be made
to report a communication failure for the other.
[A] TLM and Alarm. With this option the “PGM OUT” terminal
switches to ground if the system has a TLM fault and any
alarm condition. The output follows the length of ‘bell time
out’.
[B] Courtesy Pulse. With this option the “PGM OUT”
terminal switches to ground during the course of the
entry and exit times. It could be used to turn on a light
near the exit for the duration of the entry/exit times.
[C] PGM Squawk Output must be selected in order to use
PGM Squawk on Entry/Exit Delay options in section [60].
[D] 2nd Line Slave. With this option the “PGM OUT” terminal
switches to ground after four unsuccessful attempts have
been made to the phone number being dialed. The
output will stay switched until the panel has hung-up.
This could be used to switch the panel to a backup set of
phone lines.
[E] Kissoff Output. With this option the “PGM OUT” terminal
switches to ground after the kissoff has been received to
complete a “successful” communication to the central
station. The terminal switches to ground for 2 seconds.
[F] Remote Operation
..
..
. With this option the “PGM OUT”
terminal can be switched remotely using the DLS-1
software (version 5.3 or later).
[29] [30] [31] [32] Split Arming
“Split Arming” feature permits a single control panel to act as
two independent alarm systems, each with its own opening
and closing schedules, zone assignments and authorized
users.
The allowable zone and access code assignments to system
A or system B are described below. Typically, zones and
access codes are assigned to either Group A or Group B but
the PC3000 can be programmed for zones and access
codes that are common to both Group A and Group B.
The following four sections are each programmed the same
as section [18].
Split System Zone and Access Assignments
[29] Group A Zone Assignment for Zones 1 to 8.
Note: Zones 9 to 16 are always assigned to Group A.
[30] Group B Zone Assignment for Zones 1 to 8.
Note: Zones 9 to 16 cannot be assigned to Group B.
[31] Group A Access Code Assignment for Codes 1 to 8.
Note: Codes 9 to 16 are always assigned to Group A.
[32] Group B Access Code Assignment for Codes 1 to 8.
Note: Codes 9 to 16 cannot be assigned to Group B.
Common Zones
If a zone (1 through 8 only) is assigned to both Group A and
Group B then both Group A and Group B must be armed for
that zone to be armed.
Common Access Code
If an access code (1 through 8 only) is assigned to Group A
and Group B then that access code will arm and disarm the
entire panel.
WWW.DIYALARMFORUM.COM
To Next Page
Loading...
Need help?
General
