EasyManuals Logo
Home>Fujitsu>Server>PRIMERGY RX1330 M3

Fujitsu PRIMERGY RX1330 M3 Upgrade And Maintenance Manual

Fujitsu PRIMERGY RX1330 M3
342 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #91 background imageLoading...
Page #91 background image
RX1330 M3 Upgrade and Maintenance Manual 91
Basic software procedures
5.2.10 Verifying the memory mode
If a memory module fails, the server will reboot and the defective module will be
disabled. As a result, the current operation mode (e.g. Mirrored Channel mode)
may no longer be available due to a lack of identical memory module pairs. In
this case, the operation mode will automatically revert to Independent Channel
Mode.
I For detailed information on memory operation modes available for your
server, refer to section "Modes of operation" on page 225.
After replacing the defective module(s) the memory operation mode is
automatically reset to its original state. It is recommended to verify that the
operation mode has been correctly.
Ê Enter the BIOS.
Ê Select the Advanced menu.
Ê Under Memory Status verify that none of the memory modules are marked as
Failed.
Ê Save your changes (if applicable) and exit the BIOS.
I For detailed information on how to access the BIOS and modify settings,
refer to the corresponding BIOS Setup Utility reference manual.
5.2.11 Verifying the system time settings
I This task only applies to Linux and VMware environments.
After the system board has been replaced, the system time is set automatically.
By default, the RTC (Real Time Clock) time standard is set as the local time.
If a Linux OS is used and the hardware clock has been configured as UTC
(Universal Time, Coordinated) in the operating system, the BMC local time may
not be mapped correctly.
Ê After replacing the system board, ask the system administrator whether the
RTC or UTC time standard is to be used as system time.
I If the system time (RTC) is set to UTC, the SEL (System Event Log)
time stamps may differ from the local time.
Ê Enter the BIOS.

Table of Contents

Other manuals for Fujitsu PRIMERGY RX1330 M3

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Fujitsu PRIMERGY RX1330 M3 and is the answer not in the manual?

Fujitsu PRIMERGY RX1330 M3 Specifications

General IconGeneral
Processor ARK ID97479
CPU configuration (max)1
Intel Secure Key Technology version1.00
Intel® Quick Sync Video TechnologyNo
Intel® Hyper Threading Technology (Intel® HT Technology)Yes
HDD size2.5/3.5 \
HDD interfaceSerial ATA, Serial Attached SCSI (SAS)
Optical drive type-
Supported HDD sizes2.5, 3.5 \
Total storage capacity0 GB
Maximum storage capacity- TB
Number of HDDs installed0
Supported storage drive interfacesSAS, Serial ATA
Bus typeDMI3
SteppingB0
Scalability1S
Processor codeSR326
Processor cache8 MB
Processor cores4
Processor modelE3-1270V6
System bus rate8 GT/s
Processor socketLGA 1151 (Socket H4)
Processor threads8
Processor codenameKaby Lake
Motherboard chipsetIntel® C236
Processor frequency3.8 GHz
Processor cache typeSmart Cache
Processor lithography14 nm
Processor manufacturerIntel
Processor package size37.5 x 37.5 mm
Processor boost frequency4.2 GHz
Processor operating modes64-bit
PCI Express configurations1x16, 1x8+2x4, 2x8
Supported instruction setsAVX 2.0, SSE4.1, SSE4.2
Thermal Design Power (TDP)72 W
Maximum number of PCI Express lanes16
Memory types supported by processorDDR3-SDRAM, DDR4-SDRAM
Memory channels supported by processorDual
Memory clock speeds supported by processor1866, 2400 MHz
Memory bandwidth supported by processor (max)37.5 GB/s
Maximum internal memory supported by processor64 GB
Compatible operating systemsMicrosoft Hyper-V Server 2012 R2 Microsoft Hyper-V Server 2016 Microsoft Windows Server 2012 R2 Datacenter Microsoft Windows Server 2016 Datacenter Microsoft Windows Server 2012 R2 Standard Microsoft Windows Server 2016 Standard Microsoft Windows Server 2012 R2 Essentials Microsoft Windows Server 2016 Essentials Microsoft Windows Server 2012 R2 Foundation Microsoft Windows Storage Server 2012 R2 Standard Microsoft Windows Storage Server 2016 Standard Microsoft Hyper-V Server 2012 Microsoft Windows Server 2012 Datacenter Microsoft Windows Server 2012 Standard Microsoft Windows Server 2012 Essentials Microsoft Windows Server 2012 Foundation Microsoft Windows Storage Server 2012 Standard VMware vSphere 6.0 SUSE Linux Enterprise Server 12 Red Hat Enterprise Linux 7
Internal memory32 GB
Memory clock speed2400 MHz
Internal memory typeDDR4-SDRAM
Memory layout (slots x size)2 x 16 GB
On-board graphics card modelNot available
Power supply450 W
Number of redundant power supplies supported2
LAN controllerIntel i210
Cabling technology10/100/1000Base-T(X)
Ethernet interface typeGigabit Ethernet
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity6
Operating temperature (T-T)5 - 40 °C
Operating relative humidity (H-H)10 - 85 %
CertificationCE, RoHS, WEEE, GS, CE, CSAc/us, ULc/us, FCC Class A, VCCI:V3 Class A + JIS 61000-3-2, GOST, KC, CCC, C-TIck, BSMI
PCI Express slots version3.0
Chassis typeRack (1U)
Weight and Dimensions IconWeight and Dimensions
Depth572 mm
Width435.4 mm
Height42.8 mm
Weight13000 g

Related product manuals