EasyManuals Logo

Gigabyte GA-AX370-Gaming K7 User Manual

Gigabyte GA-AX370-Gaming K7
48 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #37 background imageLoading...
Page #37 background image
Chapter 3 Appendix
3-1 ConguringaRAIDSet
RAID Levels
RAID 0 RAID 1 RAID 10
Minimum Number of
Hard Drives
≥2 2 4
Array Capacity Number of hard drives *
Sizeofthesmallestdrive
Sizeofthesmallestdrive (Numberofharddrives/2)*
Sizeofthesmallestdrive
Fault Tolerance No Yes Yes
Before you begin, please prepare the following items:
AtleasttwoSATAharddrivesorM.2SATASSD.(Toensureoptimalperformance,itisrecommendedthat
youusetwoharddriveswithidenticalmodelandcapacity).
(Note)
AWindowssetupdisk.
Motherboard driver disk.
A USB thumb drive.
ConguringSATAControllers
A. Installing hard drives
Install the hard drives/SSDs in the SATA/M.2 connectors on the motherboard. Then connect the power connectors
from your power supply to the hard drives.
B.ConguringSATAcontrollermodeinBIOSSetup
MakesuretoconguretheSATAcontrollermodecorrectlyinsystemBIOSSetup.
Steps:
1. Turnonyourcomputerandpress<Delete>toenterBIOSSetupduringthePOST(Power-OnSelf-Test).
Under Chipset, ensure Chipset SATA Port Enable are enabled. Set SATA Mode to RAID. Then save the
settings and restart your computer.
2. IfyouwanttocongureUEFIRAID,followthestepsin"C-1."ToenterthelegacyRAIDROM,savethe
settingsandexitBIOSSetup.Referto"C-2"formoreinformation.
The BIOS Setup menus described in this section may differ from the exact settings for your motherboard.
The actual BIOS Setup menu options you will see shall depend on the motherboard you have and
the BIOS version.
C-1.UEFIRAIDConguration
OnlyWindows1064-bitsupportsUEFIRAIDconguration.
Step:
1. In BIOS Setup, go to BIOS and set Windows 10 Features to Windows 10 and CSM Support to Disabled.
Save the changes and exit BIOS Setup.
2. After the system reboot, enter BIOS Setup again. Then enter the Peripherals\RAIDXpert2Conguration
Utility sub-menu.
3. On the RAIDXpert2CongurationUtility screen, press <Enter> on Array Management to enter the Create
Arrayscreen.Then,selectaRAIDlevel.RAIDlevelssupportedincludeRAID0,RAID1,andRAID10(the
selectionsavailabledependonthenumberoftheharddrivesbeinginstalled).Next,press<Enter>onSelect
Physical Disks to enter the Select Physical Disks screen.
(Note) Referto"1-8InternalConnectors,"fortheinstallationnoticesfortheM.2andSATAconnectors.
- 37 -

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Gigabyte GA-AX370-Gaming K7 and is the answer not in the manual?

Gigabyte GA-AX370-Gaming K7 Specifications

General IconGeneral
Form FactorATX
ChipsetAMD X370
CPU SocketAM4
Memory TypeDDR4
Memory Slots4
Maximum Memory64 GB
PCIe 2.0 x1 Slots3
SATA 6Gb/s Ports6
M.2 Slots1
USB 3.1 Gen 2 Type-A Ports1
USB 3.1 Gen 2 Type-C Ports1
USB 3.1 Gen 1 Ports (Rear)4
AudioRealtek ALC1220
RAID Support0, 1, 10
Memory Speed2133/2400/2667/2933/3200 MHz (OC)
Multi-GPU Support2-Way NVIDIA SLI
LANIntel GbE LAN
PCIe 3.0 x16 Slots2 (x16/x0 or x8/x8 mode), 1 (x4 mode)

Related product manuals