26
Technical Information
Service Manual
Note:
Under energy-saving function, fan speed is defaulted at auto speed and it can’● be adjusted.
●
Under energy-saving function, set temperature can’t be adjusted. Press "TURBO"
send signal.
button and the remote controller won’t
● Sleep function and energy-saving function can’t operate at the same time. I
cooling mode, press sleep button will
energy-saving function has been set under
cancel energy-saving function. If sleep function has been set under cooling
mode, start up the energy-saving function will cancel sleep function.
8
ć
heating function
Under heating mode, press "TEMP" and "CLOCK" buttons simultaneously to start
up or turn off 8
ć
When this function is started up, " " and "8
heating function.
ć
"
heating status
will be shown on remote controller, and the air conditioner keep the
at 8
ć
. Press "TEMP" and "CLOCK" buttons simultaneously again to exit 8
ć
heating function.
Note:
● Under
ć
heating function, fan speed is defaulted at auto speed and it can’t be adjusted.
● Under
ć
heating function, set temperature can’t be adjusted. Press
"
TURBO
"
send signal.
button and the remote controller won’t
● Sleep function and
ć
heating function can’t operate at the same time. If 8
ć
heating function has been set under cooling mode, press sleep button will cancel
heating function has been set under cooling
has been set under cooling mode, start up
8
ć
heating function. If sleep function
the 8
ć
heating function will cancel sleep function.
● Under
temperature display, the remote controller will display 46
heating.
Child lock function
▲
Press "▲" and " " simultaneously to turn on or turn off child lock function. When
displayed on remote controller. If you operate
child lock function is on, " " icon is
the remote controller
, the " " icon will blink three times without sending signal to
the unit.
Temperature display switchover function
Under OFF status, press " " and "MODE
▲
" buttons simultaneously to switch temp- erature display between
ć
and
.
1.
After putting through the power, press "ON/OFF" button on remote controller to turn on the air conditioner.
2.
Press "MODE" button to select your required mode: AUTO, COOL, DRY, FAN, HEAT.
3.
Press "▲" or " " button to set your required temperature. (Temperature can’t be adjusted under auto mode).
4.
Press "FAN" button to set your required fan speed: auto, low speed, low-medium speed,medium speed, medium-high
speed,high speed.
Operation guide
▲
Replacement of batteries in remote controller
Note:
5.
Press " " button to select fan blowing angle.
1. Lift the cover along the direction of arrow (as shown in Fig 1
ǐ
).
2. Take out the original batteries (as shown in Fig 1 Ǒ).
3. Place two 7# (AAA 1.5V) dry batteries, and make sure the position of “+” polar and “-” polar is correct (as shown in Fig 2
ǒ).
4. Reinstall the cover (as shown in Fig 2
Ǔ
).
Fig.1
Fig.2
● During operation, point the remote co ntrol signal sender at the receiving window on indoor unit.
● The distance between signal sender and receiving window should be no more than 8m, and there should be no obstacles
between them.
● Signal may be interfered easily in the
room where there is fluorescent lamp
be close to indoor unit during
or wireless telephone; remote controller should
operation.
● Replace new batteries of the same model when replacement is required.
● When you don’t use remote controller for a long time, please take out the batteries.
● If the display on remote controller is fuzzy or there ’s no display, please replace batteries.
temperature automatically according to ex-factory setting to reach to the best
energy-saving effect. Press "TEMP" and "CLOCK" buttons simultaneously again to
energy-saving effect. Press "TEMP" and
exit energy-saving function.
To Next Page
Loading...
Need help?
General
