Hantek HDG2102B User Manual

SCPI Programming Reference
HDG2000 Series Arbitrary Waveform Generator 80
SOURce<n>:PULSe:TRANsition:TRAiling? [MINimum|MAXimum]
Sets the pulse edge time on the leading, trailing, or both edges of a pulse.
Parameter
Typical Return
Default 1μs
+1.000000000000000E-08
Set leading edge time on CH1 to 10 ns: SOURce1:FUNCtion:PULSe:TRANsition:LEADing
0.00000001
Set trailing edge time on CH1 to 10 ns: SOURce1:FUNCtion:PULSe:TRANsition:TRAiling
0.00000001
 The leading edge time applies to rising edge, and represents the time from the 10% threshold
to the 90% threshold of the edge; the trailing edge represents the time from the 90% threshold
to the 10% threshold.
 The specified edge time must fit within the specified pulse width and period. The instrument will
limit the edge time to accommodate the specified pulse width or duty cycle.
5.2.13 HARMonicSubsystem
SOURce<n>:HARMonic:AMPL –Harmonic amplitude
SOURce<n>:HARMonic:PHASe –Harmonic phase
SOURce<n>:HARMonic:ORDEr –Harmonic order
SOURce<n>:HARMonic:TYPe –Harmonic type
SOURce<n>:HARMonic:AMPL <sn>,<value>|MINimum|MAXimum
SOURce<n>:HARMonic:AMPL?
Set Harmonic amplitude
Parameter
Typical Return
<sn> integer, 2 to 16, default 2;
<value>Continuous real Numbers
none
Sets the amplitude of the second harmonic to 1Vpp on CH1: SOURce1:HARMonic:AMPL 2,1
SOURce<n>:HARMonic:PHASe <sn>,<value>|MINimum|MAXimum
SOURce<n>:HARMonic:PHASe? <sn>[,MINimum|MAXimum]
Set Harmonic phase.
Parameter
Typical Return
<sn> integer, 2 to 16, default 2;
<value>Continuous real Numbers, 0 to
360degrees, default 0
+9.000000000000000E+01
Set the second Harmonic phase on CH1 to 90 degrees: SOURce1:HARMonic:PHASe 2,90

Hantek HDG2102B Specifications

General

Brand	Hantek
Model	HDG2102B
Category	Inverter
Language	English

Summary

General Safety Summary

Chapter 1 Quick Start

Front Panel Overview

Chapter 2 Basic Operation

Utility Functions

Chapter 3 Features and Function

Output Configuration

Pulse Waveforms

Amplitude Modulation (AM) and Frequency Modulation (FM)

Implementing AM and FM modulation on carrier waveforms.

Phase Modulation (PM)

Implementing phase modulation on carrier waveforms.

Frequency-Shift Keying (FSK) Modulation

Implementing FSK modulation for frequency shifting.

Pulse Width Modulation (PWM)

Implementing PWM for varying pulse width.

Frequency Sweep

Configuring and performing frequency sweep operations.

Burst Mode Operation

Generating waveforms in burst mode with specified cycles.

Trigger System Overview

Chapter 4 Waveform Generation Tutorial

Chapter 5 SCPI Programming Reference

Introduction to SCPI Language

SCPI Command Subsystems List

Alphabetical listing of all SCPI command subsystems.

AM Subsystem

Commands for Amplitude Modulation (AM).

ASK Subsystem

Commands for Amplitude Shift Keying (ASK).

BPSK Subsystem

Commands for Binary Phase Shift Keying (BPSK).

BURST Subsystem

Commands for controlling burst mode operation.

CALibration Subsystem

Commands for instrument calibration.

COUNter Subsystem

Commands for counter and frequency meter functions.

DATA Subsystem

Commands for managing user-defined arbitrary waveforms.

FM Subsystem

Commands for Frequency Modulation (FM).

FREQuency Subsystem

Commands for setting output frequency.

FSKey Subsystem

Commands for Frequency-Shift Keying (FSK).

FUNCtion Subsystem

Commands for selecting output waveform functions.

HARMonicSubsystem

Commands for generating harmonic waveforms.

MARKer Subsytem

Commands for controlling sweep markers.

MEMory Subsystem

Commands for managing stored states.

MMEMory Subsystem

Commands for file system operations (USB, SD card).

OUTPut Subsystem

Commands for controlling channel output and sync signals.

PHASeSubsystem

Commands for adjusting waveform phase.

PM Subsystem

Commands for Phase Modulation (PM).

PSK Subsystem

Commands for Phase Shift Keying (PSK).

PWM Subsystem

SWEepSubsystem

SYSTem Subsystem

VOLTage Subsystem