5.8 Pair up with the Subwoofer and Rear
Surround Speakers
Automatic pairing
The subwoofer, rear surround speakers and
soundbar will automatically pair when they are
plugged into the mains sockets and turned on.
No cable is needed for connecting the three units.
• Determine the status based on the indicator
of the wireless subwoofer and wireless rear
surround speakers.
LED State Status
Fast blink
Subwoofer and the rear surround
speakers in pairing mode
Constant on
Connected / Pairing successfully
Slow blink
Connection / Pairing failed
NOTE:
- Do not press the PAIR button on the rear of
the subwoofer or the PAIR button on the rear
surround speakers(SR), except for manual pairing.
- If the automatic pairing fails, pair the subwoofer
and the rear surround speakers with the main
unit manually.
Manual pairing
1. Ensure that all cables are well connected
and the main unit is in Standby mode.
4. Press and hold the PAIR button on the rear
of the subwoofer or the PAIR button on the
rear surround speaker(SR) for 2 seconds.
The subwoofer and the rear surround speakers
will enter the pairing mode and the indicators
on the subwoofer and the rear surround
speakers will blink quickly.
2. Press the
button on the main unit or on
the remote control to switch the main unit on.
3. Press the button on the main unit or on the
remote control for 3 seconds to enter Pairing mode.
The display will scroll "SW Pairing".
5. After the wireless connection succeeded, the
Pair indicators will light up and the display on
main unit will scroll "SW_IN".
6. If the Pair indicator blink slowly, the
wireless connection has failed. Unplug
the cable of the subwoofer and then the
cable of the rear surround speakers,
reconnect the main cables after 3 minutes.
Repeat step 1 ~ 4.
NOTE:
(for example, interference from an electronic
device) around your location. Remove these
conicts or strong interferences and repeat
the above procedures.
• The subwoofer and the rear surround speakers
should be within 6m (18 feet) of the soundbar
in an open area.
• If the main unit is in On mode, and not
connected with the subwoofer and the rear
surround speakers, the indicators on the
subwoofer and the rear surround speaker(SR)
will ash slowly. Follow step 1~4 above to
pair the subwoofer and the rear surround
speakers to the main unit.
6.
Basic Operation
6.1 Standby/On
socket, the main unit will be in STANDBY mode.
• Press the
button on the unit or on the
remote control to switch the unit ON.
• Press the
button again to switch the unit
back to STANDBY mode.
• Disconnect the mains plug from the mains
socket if you want to switch the unit OFF
completely.
6.2 Auto-Standby / Auto-Wake Feature
• [Auto-Standby] Your soundbar has been
programmed to enter STANDBY mode
automatically when no audio is detected for
15 minutes. For example, this would happen
when pausing playback, or should the
soundbar be left on accidentally.
• [Auto-Wake] If a TV or an external device is
connected (HDMI eARC/OPTICAL/AUX/COAXIAL
mode), the unit will switch on automatically
when the TV or the external device is switched
on.
To disable this feature, please follow the steps
below:
1. During ON mode, pointing the remote at the
soundbar, press and hold the
button for 3
seconds to open the menu.
- The unit’s display will scroll “MENU
”.
2. Press the /
button 6 times in succession：
the display shows: Auto Wake [ON / OFF].
or
Press the /
button 7 times in
succession,the display shows: Auto Standby
.
• If the wireless connection fails again, check
if there is conict or strong interference
14
[ON / OFF].
To Next Page
Loading...
Need help?
General
Weight and Dimensions
