Hisense AX5100G User Manual

• If the rear surround speakers are disconnected
and turned o, the speaker system would auto
switch to 3.1 channel.
• If the rear surround speakers are connected
and turned on, the speaker system would
auto switch to 5.1 channel again.
12. 5.1ch and 3.1ch Auto
Switch Operation
• The subwoofer is out of range, please move
the subwoofer closer to the soundbar. Make
sure the subwoofer is within 5 m of the
soundbar (the closer the better).
• The soundbar may have lost connection with
the subwoofer. Re-pair the units by following
the steps on the section “Pairing the Wireless
Subwoofer with the Soundbar”.
• The unit may not be able to decode all digital
audio formats from the input source. In this
case, the unit will mute. This is NOT a defect.
device is not muted.
13. Troubleshooting
To keep the warranty valid, never try to repair the
system yourself. If you encounter problems when
using this unit, check the following points before
requesting service.
No power
• Ensure that the AC cord of the unit is
properly connected .
• Ensure that there is power at the AC outlet.
• Press standby button to turn the unit on.
Remote control does not work
• Before you press any playback control
• Reduce the distance between the remote
control and the unit.
• Insert the battery with its polarities (+/-)
aligned as indicated.
• Replace the battery.
• Aim the remote control directly at the sensor
on the front of the unit.
No sound
• sserP .detum ton si tinu eht taht erus ekaM
or VOL+/– button to resume normal
listening.
• Press
button on the unit or on the remote
control to switch the soundbar to standby
mode. Then press the
button again to
switch the soundbar on.
• Unplug both the soundbar and the subwoofer
from the mains socket, then plug them again.
Switch on the soundbar.
• Ensure the audio setting of the input source
(e.g. TV, game console, DVD player, etc.)
is set to PCM or Dolby Digital mode while
using digital (e.g. HDMI, OPTICAL, COAXIAL)
connection.
11. Setup Menu
1. During ON mode, press and hold the
button for 3 seconds to open the menu.
2. Select the content with
/ buttons.
3. Change the initial values for each of the
settings with VOL +/- buttons.
4. Press the
button
and exit the settings.
• If no button is pressed within 10 seconds, the
system will automatically exit the menu.
Display
(press
/
)
Description
(press VOL + / - )
1
.
(
MUSIC, MOVIE, NEWS, SPORT,
NIGHT, GAME, AI EQ)
2
Switch Surround Sound
[ON / OFF]
3
Adjust the Bass Level
4
Adjust the Treble Level
5
Adjust the Brightness
(
6
Switch Auto Wake
[ON / OFF]
7
8
Switch Auto Standby
[ON / OFF]
Switch Beep
[ON / OFF]
9
13
Set the Audio Delay
(AV SYNC)
12
Switch: DTS Neural
[ON / OFF]
Switch: BassBoost
[ON / OFF]
Switch: DTS Virtual:X
[ON / OFF]
10
Adjust DTS DRC Level: DRC 0/1/2
11
14
Adjust DTS Dialog Control
Level: DCL 0/1/2/3/4/5/6
19

Hisense AX5100G Specifications

General

TV Sound Share	No
Equalizer modes	Bass, Movie, Music
Audio output channels	5.1 channels
Soundbar mode control	Yes
Number of speakers	7
Soundbar speaker RMS power	340 W
Subwoofer type	Active subwoofer
Subwoofer connectivity	Wireless
Woofer diameter (subwoofer)	214 \
Product color	Black
Volume control	Buttons
Country of origin	China
Audio formats supported	ALAC, FLAC, MP3, MP4, WAV, WMA
Audio system	6
Wireless technology	Bluetooth, WIFI
AUX in	-
Bluetooth version	5.0
Connectivity technology	Wired & Wireless
Digital audio coaxial in	0
Power source	AC
Power consumption (typical)	0 W
Cables included	AC, Optical
Number of satellite speakers	2
Package depth	454 mm
Package width	1000 mm
Package height	237 mm
Package weight	11700 g

Weight and Dimensions

Depth	90 mm
Width	920 mm
Height	60 mm
Weight	2 g
Cord length	1 m
Subwoofer depth	304 mm
Subwoofer width	214 mm
Subwoofer height	294 mm
Subwoofer weight	4 g