EN 20
NOTE:
Selectable picture format aspect ratios may vary depending on
the input source or broadcast signal.
Aspect menu also can be displayed by pressing ASPECT on
the remote control.
•
•
Natural
In some cases, this image will display the size of standard 4:3 with
a black side bar.
Cinema Wide1 (for 4:3 format programs)
To fill the screen, the right and left edges are extended. However,
the center of the picture remains near its former ratio.
The top and bottom edges of the picture may be hidden.
Cinema Wide2 (for letter box programs)
The entire picture is uniformly enlarged-it is stretched the same
amount both wider and taller (retains its original proportion).
The top and bottom edges of the picture may be hidden.
Cinema Wide3 (for letter box programs with subtitles)
To fill the width of the screen, it is extended horizontally. However,
it is only slightly extended at the top and the bottom.
The top and bottom edges of the picture may be hidden.
Full (for 16:9 source programs)
Full will display the picture at the maximum size.
Native (for PC mode only)
Detects the resolution of the signal of the image and it will be shown
on the screen with same amount of pixels.
NOTE:
Some High Definition and/or Digital broadcasts may not allow
you to change the picture format aspect ratio.
In HDMI or COMPONENT mode with a scanning rate of 720p,
1080i or 1080p (only HDMI), only the Cinema Wide2 and Full
are available.
In PC mode, only the Natural, Full and Native are available. In
PC mode (WXGA, LE39S406/LE39H316: WXGA, WXGA+,
FHD), only the Full and Native are available.
LE39S406/LE39H316 : When the PC connected to the HDMI
terminal and 1920x1080 resolution (FHD) is selected, the top
and bottom, right and left edges of the picture may be hidden on
all picture sizes.
•
•
•
•
CC advanced
When you have selected Custom as the display method, you
can adjust the various setting listed below as follows:
This feature is designed to customize Digital Captions only.
1
Select “Setup Closed Captions”, then press or ENTER.
2
Press or to set “CC Display” to “On”.
3
Press or to select “Digital CC Preset”, then press or
to select “Custom”.
4
Press or to select “CC Advanced”, then press or
ENTER.
The CC Advanced menu will appear.
5
Press or to select the desired item, then press or to
change the setting.
CC Advanced
Text Size Auto
Text Type Auto
Text Edge Auto
Text Color Auto
Text Opacity Auto
Background Color Auto
Background Opacity Auto
You can select from among the following items and
parameters.
Text Size: Auto, Small, Standard, Large
Text Type: Auto, Style1, Style2, Style3, Style4, Style5,
Style6, Style7
Text Edge: Auto, None, Raised, Depressed, Uniform, Left
Shadow, Right Shadow
Text Color: Auto, Black, White, Red, Green, Blue, Yellow,
Magenta, Cyan
Text Opacity: Auto, Solid, Transparent, Translucent,
Flashing
Background
Color:
Auto, Black, White, Red, Green, Blue, Yellow,
Magenta, Cyan
Background
Opacity:
Auto, Solid, Transparent, Translucent,
Flashing
NOTE:
You cannot set both “Text Color” and “Background Color” as a
same color.
You cannot set both “Text Opacity” and “Background Opacity” to
“Transparent”.
Aspect Switching
You can display the image at its optimum condition by
selecting display aspect.
Selecting the picture format aspect ratio
1
Select “Video Aspect”, then press or ENTER to display
“Aspect” menu.
2
Press or or corresponding Number buttons (0-4)
to
select the desired picture format aspect ratio, as described
below.
Aspect
1.Cinema Wide1
2.Cinema Wide2
0.Natural
4.Full
3.Cinema Wide3
•
•
J3PC1421A_EN.indd 20 8/24/12 4:50:18 PM
To Next Page
Loading...
Need help?
General
