To Next PageTo Next PageTo Previous PageTo Previous Page
What does 'Need Force Calibration' mean on Honeywell BW Flex Gas Detectors?
If your Honeywell Gas Detector displays a 'Need Force Calibration' message, it means that calibration is overdue and must be performed before use. Hold the button for 3 seconds, connect to DC/SSDC, or insert it into IntelliDoX to start the calibration. Otherwise, the detector will automatically power off after 60 seconds.
What does error 4006 mean on Honeywell BW Flex?
If your Honeywell Gas Detector shows Error 4006, it indicates that sensors have failed or there is no communication. The suggested solution is to replace the sensor or the PCBA.
What does error 4004 mean on Honeywell BW Flex?
If your Honeywell Gas Detector displays Error 4004, it means the sensor is in the wrong slot. To resolve this, correct the sensor position.
What does error 1008 mean on Honeywell Gas Detectors?
If your Honeywell Gas Detector displays Error 1008, it means BLE fail. The suggested solution is to replace PCBA.
What does error 3001 mean on Honeywell BW Flex Gas Detectors?
If your Honeywell Gas Detector displays Error 3001, it means RTC fail. The suggested solution is to replace PCBA.
What does error 1007 mean on Honeywell BW Flex Gas Detectors?
If your Honeywell Gas Detector displays Error 1007, it means Data flash fail. The suggested solution is to replace PCBA.
What does error 1006 mean on Honeywell BW Flex Gas Detectors?
If your Honeywell Gas Detector displays Error 1006, it means Temperature sensor fail. The suggested solution is to replace PCBA.
How to fix 'Battery 0%' message on Honeywell BW Flex Gas Detectors?
If the Honeywell Gas Detector displays a 'Battery 0%' message, it means the battery is depleted. To resolve this, charge the rechargeable battery pack.
Why my Honeywell BW Flex doesn’t accurately measure gas?
If your Honeywell Gas Detector doesn't accurately measure gas, the following reasons may cause this issue: * The sensors require calibration. In this case, you should carry out calibration. * The detector is colder or hotter than the gas temperature. Allow the detector to reach ambient temperature before use. * The sensor filter is blocked. Replace the sensor filter.
Why does my Honeywell Gas Detectors alarm for no reason?
If the Honeywell Gas Detector alarms without reason, consider the following: * The sensor may have been exposed to the target gas. If so, the detector is operating normally; use caution in suspected areas and check the peak gas exposure reading. * Alarm setpoints might be set incorrectly. Define the alarm setpoint in Detector Configurator. * Sensors may require calibration. Carry out calibration. * There may be missing or faulty sensors. Replace the sensors. * The battery temperature may be out of acceptable range. Move to a lower temperature environment to charge the battery.
General| Humidity Range | 10% to 95% RH (non-condensing) |
|---|---|
| Alarm | Audible and visual alarms |
| IP Rating | IP66 |
| Detection Gases | Combustible gases, O2, H2S, CO, SO2, NH3, Cl2, HCN, HF, NO2, PH3, O3 |
| Sensor Type | Electrochemical, Catalytic Bead, Infrared |
| Display | LCD |
| Communication | Bluetooth |
| Operating Temperature | -20°C to 50°C (-4°F to 122°F) |
| Certifications | UL, ATEX, IECEx, CSA |
Essential safety guidelines and hazard warnings for detector usage.
Overview of the detector's function and compliance with industry standards.
Identifies physical components and explains display icons and indicators.
Steps for initial setup, including language, time, and date configuration.
Procedures for turning the detector on/off, self-test, and button functions.
Steps to connect the detector to a mobile device via Bluetooth.
Step-by-step guide for calibrating the detector's sensors.
Process for performing a bump test to verify sensor response.
Steps to perform a zero calibration in fresh air for optimal performance.
Instructions for cleaning, charging, and updating firmware.
Guidance on replacing the belt clip, sensor filter, and sensors.
Solutions for common problems and error messages encountered with the detector.
Detailed sensor specs and response to various gases.
Detector's physical characteristics and configurable settings.
Guidelines for system security and how to contact Honeywell.
