EasyManuals Logo
Home>HP>Desktop>EliteOne 800 G3

HP EliteOne 800 G3 User Manual

HP EliteOne 800 G3
141 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #115 background imageLoading...
Page #115 background image
Creating recovery media and backups
Recovery after a system failure is only as good as your most recent backup.
1. After you successfully set up the computer, create HP Recovery media. This step creates a Windows 7
operating system DVD and a Driver Recovery DVD. The Windows DVD can be used to reinstall the original
operating system in cases where the hard drive is corrupted or has been replaced. The Driver Recovery
DVD installs specic drivers and applications. See Creating recovery media with HP Recovery Disc
Creator on page 107.
2. Use Windows Backup and Recovery tools to perform the following:
Back up individual les and folders
Back up your entire hard drive (select products only)
Create system repair discs (select products only) with the installed optical drive (select products
only) or an optional external optical drive
Create system restore points
NOTE: This guide describes an overview of backing up, restoring, and recovering options. For more details
about the tools provided, see Help and Support. To access Help and Support, select Start, and then select
Help and Support.
NOTE: HP recommends that you print the recovery procedures and save them for later use, in case of
system instability.
In case of system failure, you can use the backup les to restore the contents of your computer. See Backing
up your information on page 108.
Guidelines
When creating recovery media or backing up to discs, use any of the following types of discs (purchased
separately): DVD+R, DVD+R DL, DVD-R, DVD-R DL, or DVD±RW. The discs you use will depend on the type
of optical drive you are using.
Be sure that the computer is connected to AC power before you start the recovery media creation
process or the backup process.
Creating recovery media with HP Recovery Disc Creator
HP Recovery Disc Creator is a software program that oers an alternative way to create recovery media. After
you successfully set up the computer, you can create recovery media using HP Recovery Disc Creator. This
recovery media allows you to reinstall your original operating system as well as select drivers and
applications if the hard drive becomes corrupted. HP Recovery Disc Creator can create two kinds of recovery
DVDs:
Windows 7 operating system DVD—Installs the operating system without additional drivers or
applications.
Driver Recovery DVD—Installs specic drivers and applications only, in the same way that the HP
Software Setup utility installs drivers and applications.
Creating recovery media
NOTE: The Windows 7 operating system DVD can be created only once. Thereafter, the option to create that
media will not be available after you create a Windows DVD.
To create the Windows DVD:
Backing up, restoring, and recovering in Windows 7 107

Table of Contents

Other manuals for HP EliteOne 800 G3

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP EliteOne 800 G3 and is the answer not in the manual?

HP EliteOne 800 G3 Specifications

General IconGeneral
Tcase71 °C
Bus typeDMI3
SteppingR0
Processor codeSR2BX
Processor cache6 MB
Processor cores4
Processor modeli5-6500
System bus rate8 GT/s
Processor familyIntel® Core™ i5
Processor seriesIntel Core i5-6500 Desktop series
Processor socketLGA 1151 (Socket H4)
Processor codenameSkylake
Processor frequency3.2 GHz
Processor cache typeSmart Cache
Processor lithography14 nm
Processor manufacturerIntel
Conflict-Free processorYes
Processor front side bus- MHz
PCI Express slots version3.0
Processor boost frequency3.6 GHz
Processor operating modes64-bit
PCI Express configurations1x16, 2x8, 1x8+2x4
Thermal Design Power (TDP)65 W
Maximum number of PCI Express lanes16
Memory types supported by processorDDR3L-SDRAM, DDR4-SDRAM
Memory voltage supported by processor1.35 V
Memory clock speeds supported by processor2133, 1333, 1600, 1866 MHz
Memory bandwidth supported by processor (max)34.1 GB/s
Maximum internal memory supported by processor64 GB
Discrete graphics cardNo
On-board graphics card ID1912
Discrete graphics card modelNot available
On-board graphics card modelIntel® HD Graphics 530
Maximum on-board graphics card memory1.74 GB
On-board graphics card OpenGL version4.4
On-board graphics card base frequency350 MHz
On-board graphics card DirectX version12.0
On-board graphics card dynamic frequency (max)1050 MHz
Number of displays supported (on-board graphics)3
Color gamut72 %
RGB color spaceNTSC
Display diagonal23.8 \
Native aspect ratio16:9
Product typeAll-in-One PC
Motherboard chipsetIntel® Q270
Memory slots2
Internal memory8 GB
Memory slots typeSO-DIMM
Memory clock speed2400 MHz
Internal memory typeDDR4-SDRAM
Maximum internal memory32 GB
Memory layout (slots x size)1 x 8 GB
SSD capacity256 GB
SSD interfacePCI Express
Storage mediaSSD
Optical drive typeDVD-RW
Card reader integrated-
Number of storage drives installed1
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity6
USB 3.2 Gen 2 (3.1 Gen 2) Type-A ports quantity0
Product colorBlack, Silver
Country of originChina
Antenna type2x2
Wi-Fi standardsWi-Fi 5 (802.11ac)
Ethernet LAN data rates10, 100, 1000 Mbit/s
AC adapter power180 W
Recovery operating systemWindows 10 Pro
Operating system installedWindows 7 Professional
Scalability1S
Processor ARK ID88184
Processor package size37.5 x 37.5 mm
Supported instruction setsSSE4.2, AVX 2.0, SSE4.1
Thermal solution specificationPCG 2015C
Intel Identity Protection Technology version1.00
Weight and Dimensions IconWeight and Dimensions
Depth (with stand)53.8 mm
Width (with stand)539.6 mm
Height (with stand)314.8 mm
Weight (with stand)6030 g

Related product manuals