ITech IT6522D User Manual

List Operation Commands
Copyright© Itech Electronics Co., Ltd. 62
LIST:EDIT
This command is used to select list file which has been edited.
Command syntax
LIST:EDIT <MINimum|MAXimum|1~10>
Arguments
MINimum|MAXimum|<1~10>
Example
LIST:EDIT 10
Query syntax
LIST:EDIT?
Returns
NR1
LIST:REPeat
This command is used to edit the running times of list file.
Command syntax
LIST:REPeat <MINimum|MAXimum|1~65535>
Arguments
MINimum|MAXimum|<1 to 65535>
Example
LIST:REP 2000
Query syntax
LIST:REPeat? [MINimum|MAXimum]
Returns
NR1
LIST:SEQuence:COUNt
This command is used to edit the wave count of list file.
Command syntax
LIST:SEQuence:COUNt <1-10>
Arguments
<1~10>

ITech IT6522D Specifications

General

Output Voltage	0 ~ 60 V
Frequency	50Hz / 60Hz
Operating Temperature	0°C to 40°C
Relative Humidity	< 80%
Communication Interface	USB, RS232

Summary

SCPI Command Introduction

SCPI Command Types

Explains common and subsystem commands, and message structure.

SCPI Message Types

Details program messages and response messages in SCPI communication.

SCPI Command Format

Explains SCPI command syntax, parameters, and formatting rules.

SCPI Status Registers

Status Register Bit Definitions

Table defining BIT signals for operation, query, standard, and status byte registers.

Status Register Structure

Illustrates the structural relationship between different SCPI status registers.

SCPI Command Description

STATus:QUEStionable Commands

Commands for querying and enabling questionable status events.

STATus:OPERation Commands

Commands for querying and enabling operation status events.

SYSTem:ERRor?

Reads the error information from the instrument.

SYSTem:REMote and SYSTem:LOCal

Switches the instrument between remote and local control modes.

SYSTem:RWLock

Locks the local control button, preventing mode switching.

SYSTem:COMMunicate Commands

Commands for selecting and configuring communication interfaces.

Display Related Commands

Trigger Commands

TRIGger[:IMMediate]

Creates a trigger signal for instrument operation.

TRIGger:SOURce

Sets the source for triggering instrument events.

Input Measuring Commands

MEASure Voltage Commands

Enquires the actual output voltage measurement.

FETCh Voltage Commands

Fetches the DC voltage value from the buffer.

MEASure Current Commands

Enquires the latest DC current measurement.

FETCh Current Commands

Fetches the DC current value from the buffer.

MEASure Power Commands

Enquires the latest output power measurement.

FETCh Power Commands

Fetches the power value from the buffer.

FETCh? Command

Fetches all measurements of voltage, current, and power.

MEASure? Command

Enquires the latest measurements of voltage, current, and power.

Output Commands

Source Current Level

Sets the output current level.

Source Current Limits

Sets minimum and maximum output current values.

Source Current Transition Times

Sets rising and falling times for output current.

Source Current Protection

Configures over-current protection state and threshold.

Source Voltage Level

Sets the output voltage level.

Source Voltage Limits

Sets minimum and maximum output voltage values.

Source Voltage Transition Times

Sets rising and falling times for output voltage.

Source Voltage Protection

Configures over-voltage protection state and threshold.

Source Power Level

Sets the output power level.

Source Power Limits

Sets minimum and maximum output power values.

Source Power Transition Times

Sets rising and falling times for output power.

Source Power Protection

Configures over-power protection state and threshold.

Source Resistance Setting

Sets the internal resistance value.

Source Apply Command

Output Switch Control

Load Related Commands

Load State Control

Load Selection

Load Current Settings

Sets the load current level and limits.

Load Current Transition Times

Load Current Protection

Configures load over-current protection state and threshold.

Load Power Settings

Sets the load power level and limits.

Load Power Transition Times

Load Power Protection

Configures load over-power protection state and threshold.

List Operation Commands

Wave Operation Commands

Calibration Commands

Calibration Security State

Voltage Calibration Points

Current Calibration Points

IEEE-488 Commands

*CLS Command

*ESE Command

*ESR? Command

*IDN? Command

*OPC Command

*PSC Command

*RST Command

Resets the power supply to its default settings.

*SRE <n> Command

*STB Command

*SAV Command

*RCL: Command

*TST? Command