4/18
WARNING:
Shock hazard. Do not allow any liquid to get
inside charger.
4. Symbols
The label on your tool may include the following symbols. The
symbols and their de nitions are as follows:
V volts n
0
no-load speed
A amperes ou d.c. direct current
W watts
ou a.c
alternating current
Hz hertz earthing terminal
lbf/in² (lbf/pol²) psi l litres
min minutes kg kilograms
h hours m meters
5. Important Safety Instructions for
Battery Chargers
SAVE THESE INSTRUCTIONS:
This manual contains important
safety instructions for battery chargers. Before using charger,
read all instructions and cautionary markings on charger, bat-
tery pack, and product using battery pack.
3.4. Power tool use and care
a. Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job bet-
ter and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it
on and o .
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any ad-
justments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the
power tool accidentally.
d. Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are dan-
gerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or bind-
ing of moving parts, breakage of parts and any other
condition that may a ect the power tool’s operation. If
damaged, have the power tool repaired before use.
Many
accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean.
Properly maintained
cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
g. Use the power tool, accessories and tool bits etc., in ac-
cordance with these instructions, taking into account the
working conditions and the work to be performed. Use
of the power tool for operations di erent from those intended
could result in a hazardous situation
.
3.5. Battery tool use and care
3.6. Service
a. Have your power tool serviced by a quali ed repair per-
son using only identical replacement parts.
This will ensure
that the safety of the power tool is maintained.
b. Use personal protective equipment. Always wear eye
protection.
Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for appropri-
ate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in
the o -position before connecting to power source and/
or battery pack, picking up or carrying the tool.
Carrying
power tools with your nger on the switch or energizing power
tools that have the switch on invites accidents.
d. Remove any adjusting key (wrench, screwdriver…) before
turning the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all
times.
This enables better control of the power tool in unexpect-
ed situations.
f. Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts.
Loose clothes, jewellery or long hair can be caught in
moving parts.
g. If devices are provided for the connection of dust ex-
traction and collection facilities, ensure these are con-
nected and properly used.
Use of dust collection can reduce
dust-related hazards.
a. Recharge only with the charger speci ed by the manufac-
turer. A charger that is suitable for one type of battery pack may
create a risk of re when used with another battery pack.
b. Use power tools only with speci cally designated battery
packs.
Use of any other battery packs may create a risk of injury
and re.
c. When battery pack is not in use, keep it away from other
metal objects like paper clips, coins, keys, nails, screws,
or other small metal objects that can make a connection
from one terminal to another.
Shorting the battery terminals
together may cause burns or a re.
d. Under abusive conditions, liquid may be ejected from
the battery, avoid contact. If contact accidentally occurs,
ush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause irri-
tation or burns.
e. Do not use a battery pack or appliance that is damaged
or modi ed. Damaged or modi ed batteries may exhibit
unpredictable behavior resulting in re, explosion or risk
of injury.
f. Do not expose a battery pack or appliance to re or exces-
sive temperature. Exposure to re or temperature above
60°C may cause explosion.
17/18
Malfunction / Status Cause Action
Battery charge is not
lasting as usual or is not
charging at all
New battery
Battery is not being fully charged
Charge battery until charger LED
indicator is green
Not original JACTO charger Use original JACTO charger
Not original pump (excessive load) Use original pump
Damaged charger or charger cords/
plugs
Replace charger
Battery is damaged (wet, pierced,
broken terminals…)
Replace battery
Used battery (more than 300
recharge cycles)
Battery life cycle is near the end Replace battery
Red button is pressed but sprayer does not shut o
Red button was not held/pressed
long enough
Press red button and hold for 3
seconds
Interface is damaged Contact technical assistance
10.1. Influence of climatic conditions
During application, some factors may determine the interrup-
tion of the spraying. Wind currents, for example, can a ect drop-
lets to a greater or lesser distance in terms of its size or weight.
The temperature and especially the relative humidity contribute
to the rapid evaporation of the droplets.
The ideal conditions for spraying are:
• Relative humidity: minimum 50%;
• Wind speed: 1.9 - 6.2 mph (3-10 km/h);
• Temperature below 86º F (30º C) .
These limits should be considered according to technology
application that will be used, adopting the safest class droplets
within the boundaries of each situation.
Air velocity around the
nozzle height
Description Visible signs Spraying
1.2 mph (2 km/h) Calm Smoke rises vertically
Ideal for spraying
1.2 to 1.9 mph (2 to 3 km/h) Nearly calm The smoke is tilted
1.9 to 4.3 mph (3 to 7 km/h) Light breeze
The leaves range. Feel the
light wind
Ideal for spraying
4.3 to 6.2 mph (7 to 10 km/h) Light wind
Leaves and thin branches in
constant motion
We recommend only the
drift reduction technique
6.2 to 9.3 mph (10 to 15
km/h)
Moderate wind
Moving branches. Dust and
pieces of paper are carried
by the wind
Improper for spraying
To Next Page
Loading...
Need help?
General
