Janus G3 User Manual

List of Commands for Programming Mode
NOTE: The phone enters Programming Mode after completing step 2
of the Programming Instructions.
• #0 First Phone Number *#
• #1 Second Phone Number *#
• #2 Third Phone Number *#
• #3 Fourth Phone Number *#
• #4 Identication Code *#
• #5 Programming New Password *# - Set Programming Access Code
• #7 - Records location message
• #8 - Plays back location message
• #* 1 XXX Y W Z *# - setup code (Default is: #* 1 180 1 8 3 *#)
• XXX - Call Timer [000,060-990], 000=Disable timer
• Y - Push Button Control [0-2]
[0] Push on = turn on/push again = play message
[1] Push on = turn on/push again = turn off
[2] Push and hold = turn on/release = turn off
[3-8] Push and hold to turn on for Y amount of seconds to make
a call. If pushed for less than Y amount of seconds, turn
off/push again = turn off
• W - Unit ID [1-8]
• Z - Voice Mode [0,3 or 5]
• **42 X *# - Ring Count (for incoming calls) (0-9 range, 4 = default, 0 = no
answer)
• **43 X *# - Ring Time (for outgoing calls) (18-60 range, 50 is default)
•**44 X *# - AUX1 behavior (0-2), 0 = disabled, 1 = red led, 2 = green led,
3 = VCC mode
• **45X*# - Redial, 0 = disabled (Default), 1 = Dial the number 1 more time,
2 = Dial the number 2 more times
• **8 XX *# - Set Language (1 = English: default, 2 = Spanish, X= [1-2]
(must have 2 digits)
NOTE: **8XX*# will play both messages according to the order specied.
(Ex// **812*# = English then Spanish or **821*# = Spanish then English)
NOTE: If second message is not used, enter ʻ0ʼ for that message. For
example, if you want to set to play English only you must program: **810*#.
• **7 0 *# - Ring-Thru Converse Mode (Default). With this setting, the G3
will automatically enter two way communication after it has answered an
incoming call.
• **7 1 XXXX *# - Hang Up Converse Mode - Set Remote Access Code.
NOTE: When user calls in they have 5 seconds to enter the 4 digit
password set by *71. If not or the wrong code is entered, a long beep
will be heard and the phone will turn OFF. If the correct code is entered,
3 beeps will be heard and two way communication will be established.
The speaker and microphone will both be muted until the correct code is
entered.
10

Janus G3 Specifications

General

optional AC adapter	9-12VDC/VAC @ min. 200mA
operating current range	18mA to 55mA
phone line voltage on-hook	24VDC to 70VDC (nominally 48VDC)
phone line voltage off-hook	8 to 20VDC (nominally 14VDC)
ring sensitivity	30 - 120VAC RMS
operating temperature range	32 to 122F (0 to 50C)
storage temperature range	-4 to 158F (-20 to 70C)
relative humidity	Up to 95% (non-condensing)
frequency response	550Hz - 3400Hz +/- 3db.
operational loop impedance	600 ohms

Weight and Dimensions

size	5.5in x 3.2in x 0.75in (140mm x 81mm x 19mm)
weight	0.37lbs (0.17Kg)