EasyManuals Logo
Home>JVC>Car Receiver>KD-X250BT

JVC KD-X250BT User Manual

JVC KD-X250BT
92 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #12 background imageLoading...
Page #12 background image
Pairing a Bluetooth device
When connecting a Bluetooth device to the unit for the first time, perform pairing between the unit and
the device.
Up to five Bluetooth devices can be registered in this unit.
A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any
time.
This unit supports Secure Simple Pairing (SSP).
1
Search and select “JVC UNIT” on the Bluetooth device.
BT PAIRING flashes on the display.
For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN) code
immediately after searching.
2
Perform (A) or (B) depending on what scrolls on the display.
For some Bluetooth devices, pairing sequence may vary from the steps described below
(A) If “[Device Name]”#“XXXXXX”#
“VOL – YES”#“BACK – NO” scrolls on the
display,
XXXXXX is a 6-digit passkey randomly
generated during each pairing.
Operate the Bluetooth device to confirm
the passkey.
Ensure that the passkey which appears
on the unit and Bluetooth device is the
same.
Select “YES” to confirm the passkey.
(B) If “[Device Name]”#“VOL – YES”#
“BACK – NO” scrolls on the display,
(1) If “PAIRING”#“PIN 0000” scrolls on the
display, enter the PIN code “0000” into the
Bluetooth device.
You can change to a desired PIN code before
pairing. (' page 22)
Select “YES” to start the pairing.
(2) If only “PAIRING” appears, operate the
Bluetooth device to confirm pairing.
After pairing is successful, PAIRING COMPLETED appears on the display.
The unit will establish a connection with the newly paired Bluetooth device, lights up on the
display and you can now control the Bluetooth device through the unit.
will light up when a phone is connected.
will light up when an audio device is connected.
Once the connection is established, the device is registered to the unit and there is no need to
perform the pairing again unless you delete the registered device.
Some Bluetooth devices may not be able to connect to the unit after pairing. Connect the device to
the unit manually. Refer to the instruction manual of the Bluetooth device for more information.
See page 13 for Bluetooth compatibility check mode operation.
Bluetooth connection
12
|ޓENGLISH
2012/11/22ޓ10:10:26KD-X250BT_J_EN

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the JVC KD-X250BT and is the answer not in the manual?

JVC KD-X250BT Specifications

General IconGeneral
MP3 playbackYes
Playback disc formatsCD audio
Audio formats supportedAAC, MP3, WAV, WMA
Tuner typeHS-IVi
AM band range530 - 1700 kHz
FM band range87.9 - 107.9 MHz
Supported radio bandsAM, FM
Preset stations quantity24
Impedance4 Ω
Product colorBlack
Volume controlRotary
Frequency range5 - 20000 Hz
CD changer capacity1 discs
Disc types supportedCD
Equalizer bands quantity3
Signal-to-Noise Ratio (SNR)98 dB
USB version2.0
Bluetooth profilesA2DP, AVRCP
USB ports quantity1
FilterHigh-Pass Filter/Low-Pass Filter
Disc playback modesRandom, Repeat track
Maximum output power200 W
Amplifier output power80 W
Weight and Dimensions IconWeight and Dimensions
Dimensions (WxDxH)181.7 x 159 x 52.7 mm

Related product manuals