JVC KD-X250BT User Manual

Connecting/Disconnecting a
registered device manually
To connect
1
(Hold)
-<BLUETOOTH>
-<PHONE>/<AUDIO>
-<CONNECT>
2
Select <CONNECT>.
“CONNECTING”#“[Device Name]” scrolls on the
display when the unit is connecting to the device.
“CONNECTED”#“[Device Name]” scrolls on the
display when the device is connected.
3
Select the desired device.
4
Press MENU to exit.
To disconnect
1
(Hold)
-<BLUETOOTH>
-<PHONE>/<AUDIO>
-<DISCONNECT>
2
Select <DISCONNECT>.
“DISCONNECT”#“[Device Name]” scrolls on the
display when the device is disconnected.
3
Select the desired device.
4
Press MENU to exit.
Deleting a registered device
(Hold)
1
-<BLUETOOTH>
-<DELETE PAIR>
- [Device name]
-<DELETE YES>
“DELETED” appears when the device is deleted.
2
Select <DELETE YES>.
3
Press MENU to exit.
Bluetooth compatibility check
mode
You can check the connectivity of the supported
profile between the Bluetooth device and the
unit.
(Hold)
(Hold about
3 seconds)
“BLUETOOTH”)“CHECK MODE” appears.
“SEARCH NOW USING PHONE”#“PIN IS 0000”
scrolls on the display.
1
Enter check mode.
2
Search and select “JVC UNIT” on the
Bluetooth device within 3 minutes.
3
Perform pairing (A), (B) or (C) depending
on what appears on the display.
(A) “PAIRING”#“XXXXXX” (6-digit passkey):
Ensure that the same passkey appears on the unit
and Bluetooth device, then operate the Bluetooth
device to confirm the passkey.
(B) “PAIRING”#“PIN IS 0000”:
Enter “0000” on the Bluetooth device.
(C) “PAIRING”:
Operate the Bluetooth device to confirm pairing.
After pairing is successful, “PAIRING OK”#
“[Device Name]” appears and Bluetooth
compatibility check starts.
If “CONNECT NOW USING PHONE” appears,
operate the Bluetooth device to allow
phonebook access to continue.
The connectivity result flashes on the display.

“H.FREE OK” *1 and/or “A. STREAM OK” *2 #
“[Device Name]”: Compatible

“CONNCT FAIL”)“TRY CONNECT”: Not
compatible
*1: Compatible with Hands-Free Profile (HFP)
*2: Compatible with Advanced Audio
Distribution Profile (A2DP)
After 30 seconds, “PAIRING DELETED” appears to
indicate that pairing has been deleted, and the
unit exits check mode.

To cancel check mode, turn off the unit by
pressing and holding SOURCE.

Delete the pairing on the Bluetooth device
before pairing with this unit. (' page 12)
Bluetooth姞 connection
ENGLISHޓ|
13
2012/11/22ޓ10:10:26KD-X250BT_J_EN

JVC KD-X250BT Specifications

General

MP3 playback	Yes
Playback disc formats	CD audio
Audio formats supported	AAC, MP3, WAV, WMA
Tuner type	HS-IVi
AM band range	530 - 1700 kHz
FM band range	87.9 - 107.9 MHz
Supported radio bands	AM, FM
Preset stations quantity	24
Impedance	4 Ω
Product color	Black
Volume control	Rotary
Frequency range	5 - 20000 Hz
CD changer capacity	1 discs
Disc types supported	CD
Equalizer bands quantity	3
Signal-to-Noise Ratio (SNR)	98 dB
USB version	2.0
Bluetooth profiles	A2DP, AVRCP
USB ports quantity	1
Filter	High-Pass Filter/Low-Pass Filter
Disc playback modes	Random, Repeat track
Maximum output power	200 W
Amplifier output power	80 W

Weight and Dimensions

Dimensions (WxDxH)	181.7 x 159 x 52.7 mm