33_555533333333; aJ333333a3J333_
h_._._._._: SECTION 2 _4_;_ HOW YOUR WATER SOFTENER WORKS
A. FACEPLATE TIMER FEATURES
S
C
T
N
JJJJJJJJJJJJJJ_JJ
JJ_JJJ_JJ_JJ_JJ
JJJ_JJJJ_J_JJI
JJJ J_JJJJJJ,
JJJ J_JJJJJ_
JJJ JJ_JJJJ_
JJ_J JJJJJ_JJJ_
JJ_ JJJJ_JJJ_
JJJ JJJ_JJJJJJ
J_J JJJ_J_JJ
JJJ_J_J_JJ_JJ
J_J_JJJJ_J_JJ_
_JJJ_JJJJ_J4JJJJ_
• EXTRA RECHARGE
Sometimes, a manually started
regeneration (recharge) may be
desired, or needed. Two exam-
ples are:
- You have used more water than
usual (guests visiting) and you
may run out of soft water before
the next timer started regenera-
tion.
- You did not refill the softener
with salt before it was gone. After
you refill with salt:
You can start a regeneration right
away, or you can set the timer to
regenerate at the next 2:00 AM (or
other preset recharge time). Do
the following.
• RECHARGE NOW
Press the ON/OFF-HOLD but-
ton and hold until *RECHARGE
NOW, Serv and Fill begin to flash
in the display. Upon reaching
fill, the first cycle of regenera-
tion, the flashing Serv turns off and Fill is on steady.
RECHARGE continues to flash. This regeneration
willlast for about 2 hours. After the 2 hours, you will
have soft water again.
--_e .... I'L.II_-I I
*Note:
If the CLEAN feature is set to ON, a cleaning back-
wash (CLEAN and Bkwsh or Rinse flashes in the dis-
play, along with the minutes of the clean cycle re-
maining) precedes the recharge.
• RECHARGE TONIGHT
Press and release (do not hold) the "'Z_t q,nN ,,,,
-i " N_IO
ON / OFF-HOLD button. RE- ,_,_,_o_,_
CHARGE TONIGHT flashes in
the display, and the softener be-
gins regeneration at the next
preset recharge time. Press and release the ON
OFF-HOLD button once more if you decide to can-
cel the regeneration, and RECHARGE TONIGH'I_
• SALT MONITOR SYSTEM
The faceplate timer has a low salt monitor with an
indicator light to remind you to refill the storage
tank with salt. To set this monitor system:
i_ Lift the salt hole cover and level the salt in the
storage tank.
m The salt level decal, on the brinewell inside the
tank, has numbers from 0 to 8 (see drawing be-
low). Observe the number the leveled salt is at
or closest to.
m
Now, press the SALT LEVEL ADJUST button
until black bars display up to the salt level num-
ber. For example, the pictures below show the
salt level at 6.
!!
ILl
Finally, set the level you want the low salt indi-
cator light to come on. Press the SIGNAL LIGHT
ADJUST button until a (÷) shows opposite this
number. In the example below, the light will
come one when the stored salt drops to level 2.
At level 2, the storage tankis about 1/3 full. This
is the lowest you should allow the stored salt
level to drop to.
If you want to turn the salt monitor off, press the
SIGNAL LIGHT ADJUST button until OFF
shows above.
Note:
For accurate salt monitor operation, always use
nugget or pellet water softener salt. See page 1-6.
If potassium chloride is used, be sure to adjust the
timer to the KC1 setting on page 1-4.
salt
level
2-1
To Next Page
Loading...
Need help?
General
