Kenwood KR-694 User Manual

tr
in case of difficulty
Remote control unit
Remote
control
operation
is
not
possible.
|
#
Batteries
are
exhausted.
®
Replace
with
new
batteries.
“>
(P.
10)
e The remote control unit is too far away from | @ Operate the remote control unit within the
the main system, controlling angle is too conirollable range.
large, or there Is an obstacle in between,
@
The
audio
cords
and
system
control
cords
are
|
@
Connect
properly
referring
to
“System
not
connected
properly,
connection".
+
(P.4]
@ The source component to be operated does [| @ Place the tape(s} or CD in the source com-
not contain the tapets) or CD. ponent to be played.
@ An attempt is made to play a tape which is | e Wait unit! the recording is completed.
being recorded in the cassette deck.
Amplifier
Se cepa tats decks
Sound
is
not
output.
@
The
speaker
cords
are
disconnected.
e
Connect
them
properly
referring
to
“Sys-
tem
connection”.
@
The
VOLUME
is
set
to
the
minimum
position.
e
Adjust the
volume
to
a
proper
level,
_
e@
The
sound
is
muted.
(The
MUTING
indicator
|
@
Press
the
MUTING
key
toOFF.
+
is
blinking.)
e
The
SPEAKERS
switches
are
set
to
OFF..
®
Set
the
SPEAKERS
switch(es)
to
ON.
®
The
TAPE
2
key
is
set
to
ON.
@
Set
the
TAPE
2
key
to
OFF.
The
STAND
BY
indicator
blinks
and
sound
|
@
Speaker
cords
are
short-
circuited.
@
Turn
the
power
off,
eliminate
the
short-circult-
is
not
output.
ing,
then
turn
on
the
power
again,
@ The speaker cord is disconnected. @ Connect it properly referring “System con-
nection”,
e The BALANCE control is set to an extreme | @ Adjust the Left/Right balance.
position.
Sound
is
not
output
from
the
Surround
|
e
The
rearspeaker
cords
and/or
center
|
e
Connect
them
properly
referring
to
"Sys-
rear
speaker
and/or
center
speaker,
or
speaker
cord
are
disconnected.
tem
connection”,
their
sound
is very
small.
e@
A
surround
mode
is
not
selected.
@
Select
a
surround
mode.
e@
The
REAR
VOL.
and/or
CENTER
VOL.
con-
| #
Adjust
the
REAR
VOL.
and
CENTER
VOL.
trols
are
set
to
the
minimum
level.
controls.
A
hum
noise
is
generated
when
PHONO
|
»
The
audio
card
from
the
turntable
is
not
in-
|
e
Insert
the
audio
cord
plugs
securely
into
input
selector
key
is
pressed.
serted
securely
into
the
PHONO
jacks.
the
PHONO
jacks.
®
The
turntable
is
not
grounded.
@
Connect
the
grounding
wire
to
the
GND
terminal
on
the
rear
panel.
@ No antenna ts connected. e Connect an antenna.
@ The broadcast band is not set properly. @ Set the broadcast band properly.
e The frequency of the desired station is not | @ Tune the frequency of the desired station,
tuned
+
Pi5)
Interference.
e
Noise
due
to
ignition
noise
of
an
automobile.
|
@
Install
the
outdoor
antenna
apart
from
the
road.
e
Noise
due
to
an
influence
from
an
electric
|
®
Turn
off
the
power of
the
appliance.
appliance.
#
Noise
due
toanearby
TV
set.
@
Install
the
system
more
apart
from
the
TV
set.
A
station
which
was
preset
cannot
be
re-
|
®
The
preset
station
belongs
to
a
frequency
|
@
Preset
a
station
with
a
receivable
fre-
ceived
by
pressing
the
corresponding
nu-
that
cannot
be
received,
quency.
meric
key.
@
The
preset
memory
was
cleared
because
the
|
@
Preset the
station
again.
power cord had been unplugged for a long
period of time.
1.
This
system
is
microprocessor-controlled,
so
malfunction
may
occur
due
to
external
noise
or
interference
noise.
In
such
a
case,
unplug
the
power cord,
plug
it
and
turn
power
on
again.
2.Do
not
use
contact
cleaners
because
it
could
cause
a
malfunticon.
Be
specially
careful
against
contact
cleaners
containing
oil,
because
they
may
deform
the
plastic components.

Kenwood KR-694 Specifications

General

Brand	Kenwood
Model	KR-694
Category	Stereo Receiver
Language	English