EasyManuals Logo

Kenwood TH-F7E User Manual

Kenwood TH-F7E
60 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #21 background imageLoading...
Page #21 background image
17
6 MEMORY CHANNELS
NAMING A MEMORY CHANNEL
You can name memory channels using up to 8
alphanumeric characters. When you recall a named
memory channel, its name appears on the display in
place of the stored frequency. Names can be call
signs, repeater names, cities, names of people, etc.
1 Press [MR] to recall your desired memory
channel.
2 Press [F], [MN<->f] to enter memory name input
mode.
The entry cursor appears.
3 Turn the Tuning control or press [ ]/ [ ] to select
the first character.
•You can enter alphanumeric characters plus
special ASCII characters. Refer to the
following table for the available characters.
Press [MONI] to delete the character at the
cursor position.
•You can also use the numeric keypad to enter
a character (Special ASCII characters are not
available). For example, each press of [2]
switches entry as a, b, c, 2, A, B, C and then
back to a.
•While pressing and holding [LAMP], turn the
Tuning control to jump to the first character of
each ASCII character group.
4 Press [ ].
The cursor moves to the next digit.
5 Repeat steps 3 and 4 to enter up to 8 digits.
Pressing [ ] after selecting the 8th digit
completes the programming.
•To complete programming before entering less
than 8 digits, press [MNU] or press [ ] twice.
Press [ ] to move the cursor back.
Press [PTT] ([F], [VFO], [MR], or [CALL]) to
cancel the entry.
After storing a memory name, pressing [MN<->f]
switches the display between the memory name and
the frequency.
Note:
You can also name the DTMF memory channels {page 30}
and Information Channels {page 20} but you cannot name the
Call channel {page 19}.
You cannot assign a memory name to a channel that does not
contain data.
You can overwrite stored names by repeating steps 1 to 5.
The stored name is erased when you clear the memory
channel data.
Available Characters Using the Numeric Keypad
Available Characters Using the Tuning Control
FMTD
yeK
sretcarahCelbaliavA
1 qz1QZ
2abc2ABC
3def3DEF
4ghi4GHI
5 jkl5JKL
6mno6MNO
7prs7PRS
8tuv8TUV
9wxy9WXY
0ecaps0
#
?! ' . ,–/
&# ( ) <> ;
:"@
ABCDEFGH I J
KLMNOPQRST
UVWXYZ [
\
]^
_
`abcdefgh
i
jklmnopqr
s
tuvwxyz{ |
}
~PS!"#$%&
() +,–. /01
23456789: ;
<=>?@
ÀÁÂÃÄÅÆÇÈÉ
ÊË ÌÍÎÏ ÑÒÓ
ÔÕÖØÙÚÛÜ
ߌàáâãäåæ
çèéêë ìíîï
ñòóôõöœøùú
ûü Ÿÿ
´
y
ˆ
S
´
Y
ˆ
s
Additional Characters
Available Characters

Table of Contents

Other manuals for Kenwood TH-F7E

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Kenwood TH-F7E and is the answer not in the manual?

Kenwood TH-F7E Specifications

General IconGeneral
Frequency Range TX144-146 MHz, 430-440 MHz
Receiver SystemDouble conversion superheterodyne
Impedance50 Ohms
ModesFM, AM, WFM
Battery TypeLithium-Ion
Receiver Sensitivity0.16 µV (12dB SINAD)
Selectivity12 kHz (-6 dB), 25 kHz (-60 dB)
Voltage7.4 V
Dimensions58 x 140 x 35 mm
Output Power5 / 2.5 / 0.5 / 0.05 W
RF Power Output5 W (VHF), 5 W (UHF)

Related product manuals