Kenwood VR-209 User Manual

Front
speaker We 8
. Listening _
|
7
Surround
“ae
Psttion
\
f
speaker
\
Front
speakers
Place
to
the
front
left
and
right
of
the
listening
position.
Front
speakers
are
required
for
all
surround
modes.
Center
speaker
Place
front
and
center.
This
speaker
stabilizes
the
sound
image
and
helps
recreate
sound
motion.
Be
sure
to
connect
a
center
speaker
when
using
the
Dolby
3
Stereo
mode.
Surround
speakers
;
Place
to
the
direct
fett
and
right,
or
slightly
behind,
the
listening
position
at
even
heights.
approximately
1
meter
above
the
ears
of
the
listeners
These
speakers
recreate
sound
motion
and
atmosphere.
Required
for
surround
playback.
Subwoofer
.
Reproduces
powerful
deep
bass
sounds.
* Although the ideal surround system consists of all the speakers
listed above. if you don't have a center speaker or a subwoofer, you
can
divide
those
signais
between
the
available
speakers
in
the
speaker
settings
steps
to
obtain
the
best
possible
surround
repro-
duction trom the speakers you have available. ~ 13.
Channel space switching
_ (Except for the USA, Canada, UK, Europe and Australia}
The space between radio channels has been set to the one that
prevails in the area to which the system is shipped. However. if the
current
channel
space
setting
does
not
match
the
setting
in
the
area
where
the
system
is
to
be
used.
for
instance
when
vou
move
trom
area
1
or
area
2
shown
in
the
foltowing
table
or
vice
versa,
properreception
of
AM/FM
broadcasts
cannot
be
expected.
in
thts
case,
change
the
channel
space
setting
in
accordance
with
your
area
by
reterring
to
the following tabie.
Area
CHANNEL
Space Frequency
1 USA. Canada and South FM: 100 kHz
American countnes AM. 10 kHz
FM. 50 KHz -
AM: 9 kHz
Other countries
@ Turn power off.
@
Hold
down
the
BAND
key
of
the
main
unit
for
more
than
2
seconds.
Perform
each
of
the
following
steps
within
5
seconds.
©
Select
the
mode
by
using
the
MULTI
CONTROL
knob
of
the
|
main unit.
Each press switches the space frequency alternately.
@ "FS50/A9" (FM 50 kHz. AM 9 kHz)
L. @ “FtOO/A10" (FM 100 kHz. AM 10 kHz}
rl
Li
Blinks. | Pod i
Cit
Et
i
i/
© Establish the selection by pressing the BAND key.
Preparing the remote control i
Operation
Loading the batteries
@ Remove the cover.
© Insert the batteries. 1
* Insert four AAA-size (LRO3) batteries as inarcated by the polarity
|
markings |
a ee ee
When the STANDBY indicator is lit. the power turns-ON when you press
the POWER key on the remote control. When the power comes ON,
press the key you want to operate
Operating range
(Approx.)
Remote sensor
ney
iq
S500 80
9090
is
etOge
Model: RC-RO607
Infrared ray system
* When pressing more than one remote control key successively,
press the keys securely by leaving an interval of 1 second or more
between keys.
Notes
1
2
a
The suppiied batteries may nave shorter lives than orainary batteries
due to usé during operation checks
Repiace ai! four baiieries with new cnes when you notice a shortening
of the distance irom whicn tne remote control will operate or if the
remote contro: blip ks 5 times wnen you press ancey. Tre remote controi
is designed to retain. set up codes in memory while you change
batteries
Placing tne rerrcte sensor in direct suniignt. of in direct light trom a
high trequency fluorescent lamp may cause a madunctior
In such a case. change thé :ocaton at tne system installation to
prevent malfurctior.

Kenwood VR-209 Specifications

General

Brand	Kenwood
Model	VR-209
Category	Stereo Receiver
Language	English