Kenwood VR-209 User Manual

i PRL LALLE ELLE LLL BEN OT LELLILL LLL ANS AE TERRA ELEN LI REE LEDER ENE S SERENE:
Muting the sound.
MUTE Jets you mute the sound of the speakers.
Press the MUTE key.
; PODS. | 2m
= MUTE SW
| LIN [_
Blinks
To cancel
Press the MUTE key again so that the “MUTE” indicator goes off.
* Muting can also be cancelled by adjusting the voiume.
SOURCE DIRECT ala yback (. (analog sources only)
Use tnis function to pass the source material direct to the amplifier.
bypassing any audio processing
Press the SOURCE DIRECT key.
*Eitner
press
the
LISTEN
MODE.
SOUND.
and
SETUP
keys.
or
Switch
to anotner
input
source
to cance!
SOURCE
DIRECT
play-
oack
To cancel
Press again.
¢if SOURCE DIRECT playback was activated when using a sur-
round mode. cancelling it reactivates the previous surround mode.
Listening with headphones
@ Press the SPEAKERS A or B key sc that the speaker indicator
goes off,
Make sure the SPEAKERS tnaicators are turned oft.
{
= "7! ca fy
Sra a Be j
* If you turn off all of the speakers when in the surround mode tne
mede ts canceited as well, resuiting in stereo playback
© Connect headphones to the PHONES jack.
To adjust the balance
Use the test tone feature. ~
Recording audio
ea Ln aa
SHENLEY DIN
MONITOR
fs, .
i! r™\ vi ijl
eo08d O10) WH
INPUT SELECTOR
Recording a music source
© Use the input selector to select the source (other than “TAPE")
you want to record.
@ Set the cassette deck to record.
© Start playback, then start recording.
Cop ying lapes is
MONITOR — TAPE copying
@ Press the MONITOR key. a
STERECSWowrTOr
© Use the input selector to select a source other than “TAPE.”
© Start playback on the cassette deck connected to the MONITOR
jacks and start recording on the cassette deck connected to the
MD/TAPE jacks.
L TAPE — MONITOR copying
@ Use the input selector to select “TAPE.”
@ Start playback on the cassette deck connected to the MD/TAPE
jacks and start recording on the cassette deck connected to the
MONITOR jacks.
¢ To copy tapes using a double cassette deck, refer to the instruc-
tion manual of the dounie cassette deck.
MONITOR function (analog sources only)
You
can
connect
a
cassette
deck
or
graphic
equalizer
to
the
MON!-
TOR
Jacks
of
the
receiver
if
a
graphic
equalizer
is
connected.
the
MONITOR
key
should
be
left
in
the
on
position.
Alternately.
it
a
|
Cassette
deck
equipped
with
a
3-head
system
is
connected
to the
MONITOR
Jacks.
you
will
be
able
to
monitor
the
just-recordea
signal
while
making
recordings
on
the
cassette
deck
By
switching
the
MONITOR
key
on
and
off.
you
can
compare
the
sound
of
the
source
signal
and
the
just-recordea
signal.
For
more
information,
reter
to
the
instruction
manual
of
the
connected
component
Recording video
@ Use the input selector to.select the video source (other than
“VIDEO1”) you want to record.
@ Set the video deck connected to VIDEO 1.to record.
© Start playback, then start recording.

Kenwood VR-209 Specifications

General

Brand	Kenwood
Model	VR-209
Category	Stereo Receiver
Language	English