Makita DPC 7000 User Manual

Replacing the return spring
~~
-
Remove the fan housing (see above under “Replacing the
starter cable”).
Take off circlip
(N1) (circlip pliers, see “Accessories”).
Remove the cable pulley
(A/2).
Unscrew screw (A/3) and carefully remove spring housing
-
-
-
W4).
CAUTION: Danger of injury! If the spring is broken it may
pop out!
NOTE:
The old spring should be recycled.
-
Hold the fan housing as shown in Fig. B and strike against
a suitable surface (e.g. old newspapers - the spring is
greasy!).
CAUTION: Danger of injury! Hold the fan housing firmly so
that the old spring pops out and can relax its tension safely.
Replacement return springs come under tension in a wire ring.
Before installing, lightly grease the new spring with multi-
purpose grease, order
No. 944 360 000.
- With the spring still tight in the in wire ring, press it into the
fan housing. The wire ring will automatically be scraped off.
Turn the cable pulley slightly when putting it back on, until
you hear it catch. Put the circlip back on.
Wind on the starter cable as described above under “Re-
placing the starter cable”.
When replaceingfan housing, it may be necessaryto pull the
starter cable lightly
so that the cable pulley catches.
-
-
-
Cutting attachment in
central /side position
NOTE: The Power Cut is delivered with the cutting attachment
mounted in the middle position
(C). For cutting up against
obstacles, such as curbs orwalls, the cutting attachment can be
mounted to one side
(D). Use this position only when actually
necessary, and afterwards return the cutting attachment to the
middle position. In this position the Power Cut has better bal-
ance, is easier to guide, and is not as fatiguing for the operator.
Repositioning the cutting
tachment
(Model 7000,7001)
-
Remove the cutting disc and pull the second pressure disc off
the shaft (see also “Cleaning the Protective Hood).
Dismountthe cutting attachment (seel‘changing theV-belt”).
-
-
Loosen the knob (E/5) and turn the protective hood so that
one of the large holes is facing the adjusting screw (E/6).
Unscrew the knob and remove the spring washer (E/7).
Pull
out the adjusting screw through the hole and remove the
spacer ring (E/8).
Mount the cutting attachment and protective hood in the side
position. See “installing the Drive Arm and Cutting Disc” and
“Tightening the V-Belt”.
-
-
20

Makita DPC 7000 Specifications

General

Brand	Makita
Model	DPC 7000
Category	Saw
Language	English

Summary

Introduction and Safety

Delivery Inventory and Symbols

Lists included parts and explains important safety and operational symbols.

General Safety Guidelines

Essential rules for safe operation and user responsibilities.

Personal Protective Equipment

Mandatory gear for head, eyes, ears, hands, and respiratory protection.

Fuel Handling and Refueling Safety

Procedures for safe refueling to prevent fire and environmental hazards.

Operational Safety Procedures

Rules for starting, operating, and stopping the Power Cut safely.

Operating Procedures

Cutoff Disc Usage and Safety

Proper mounting, use, and safety precautions for cutting discs.

Kickback and Lock-in Prevention

Understanding and avoiding dangerous kickback and lock-in situations.

Work Methods and Techniques

Best practices for efficient and safe operation, including footing and cutting angles.

Cutting Metals

Techniques and safety tips for cutting various metal materials.

Cutting Masonry and Concrete

Procedures for cutting stone, concrete, and masonry with safety advice.

Transport and Storage

Guidelines for safely moving and storing the Power Cut unit.

Setup and Adjustment

Installing Drive Arm and Cutting Disc

Step-by-step guide to attaching the drive arm and cutting disc assembly.

V-Belt Tensioning and Disc Mounting

Procedures for V-belt adjustment and secure cutting disc installation.

Fuel and Oil Mixture

Correct ratios and procedures for mixing fuel and two-stroke oil.

Engine Starting and Stopping

Steps for cold and warm starting, and procedures for stopping the engine.

Carburetor Adjustment

Guide to adjusting the carburetor for proper idling and acceleration.

Maintenance Procedures

Changing the V-belt

Procedure for replacing the worn or damaged V-belt.

Cleaning the Protection Hood

How to clean the protective hood to maintain visibility and safety.

Air Filter Maintenance

Instructions for cleaning or replacing the air filter for engine health.

Spark Plug Replacement

Steps for inspecting and replacing the spark plug for reliable ignition.

Starter Cable and Return Spring Replacement

Instructions for replacing the starter cable and return spring.

Cutting Attachment Adjustment

How to reposition the cutting attachment for different cutting tasks.

Technical Data, Accessories, and Support

Technical Specifications and Components

Detailed specifications and labeled diagrams of the Power Cut.

Special Accessories Overview

Information on optional accessories like diamond discs and trolleys.

Periodic Maintenance Schedule

Recommended maintenance tasks and intervals for long-term reliability.

Troubleshooting Common Issues

Identifies malfunctions, observations, and likely causes with solutions.

Spare Parts and Service Information

Guidance on using original parts and contacting authorized service centers.

Factory Service Centers and Notes

Listing of service centers and space for user notes.