62
ENGLISH
BASIC
CONNECTIONS
BASIC OPERATION
ADVANCED
CONNECTIONS
SETUP
ADVANCED
OPERATION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
ADVANCED
OPERATION
CLEARING STORED PRESET CHANNELS
You can remove preset channels from the memory
using the following procedure.
3.2.
2
1.
Recall the preset number to be cleared with
the method described in ”PRESET SEARCH
MODE”.
2.
Press the MEMORY button on the front panel
or the MEMO button on the remote controller.
3.
The stored preset number blinks in the display
for 5 seconds. WhiIe blinking, press the CLEAR
button on the front panel or CL button on the
remote controller.
4.
“xx CLEAR” appears on the dispIay to indicate
that the specified preset number has been
cleared.
Note:
• To clear all stored preset channels, press and hold
the T-MODE and the ENTER buttons on the unit
for two seconds.
PARENTAL LOCK
This function is used to lock channels you do not
want to receive.
SETTING/RELEASING PARENTAL LOCK
5.2.3. 5.
5
3.
1.
Tune to the channel that you want to set
parental lock.
2.
Press the T-MODE button on the main unit or
the P.LOCK button on the remote controller.
PASSWORD
3.
When [PASSWORD ****] appears, use the
cursor buttons on the main unit or remote
controller, or the numeric buttons on the remote
controller, to enter a password (4 digits), then
press the ENTER button on the main unit or the
remote controller.
Note:
The password is set to 9999 when shipped from the
factory.
PASWORD OK!
SR001 abcdefg
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
4.
When the correct password is entered,
[PASSWORD OK!] is displayed and the display
fl ashes “✔” or “:”.
5.
Set parental lock on/off using the 3 / 4 cursor
buttons on the main unit or remote controller,
then confirm the setting using the ENTER
button on the main unit or remote controller.
“✔” Lock status
“:” Unlock status
You can unlock all locked channels at this time
by pressing the CLEAR button on the main
unit or CL button on the remote controller for 5
seconds. When “ALL UNLOCK?” is displayed,
press the ENTER button on the main unit or
remote controller. “UNLOCKING..” is displayed
and all locked channels are unlocked.
Notes:
• If you mistakenly enter the wrong password, you
will be asked to reenter the password.
• You can exit parental lock mode using the EXIT
button on the main unit or CLEAR button on the
remote controller.
• No sound will be output when you tune to a locked
channel.
• Although parental lock can be set for more than one
channel, all channels will share the same password.
• You cannot set Parental Lock for Channel 0.
PRESET SCAN
2
1.
Press the TUNE button twice within two
seconds on the remote controller.
2.
Press the BAND button to select SIRIUS
band.
3.
press the P.SCAN button on the remote
controller.
4.
Preset channels are recalled in sequence (No.1
→ No.2 → etc.) for about 10 seconds each. The
time changes by the received condition. No
stored preset number will be skipped.
5.
Pressing the 2 cursor button during prescanning
speeds up scanning.
Also, pressing the 1 cursor button returns to
the previous preset channel.
6.
When the desired preset channel is received,
cancel the preset scan operation by press the
P.SCAN button.
SR6003U01ENG34.indd62SR6003U01ENG34.indd62 08.8.11:08:09PM08.8.11:08:09PM
To Next Page
Loading...
Need help?
General
