Matrix 7xe User Manual

36
CHAPTER 8: TROUBLESHOOTING
8.2 ERROR CODE LIST
CODE CLASS DESCRIPTION MACHINE SOLUTION
01A1 C Incline calibration error A
a.
It occurs when the calibration time is too long or the calibration distance is too
short.
b. Don’t fix the incline motor tube then turn on the power.
- If the console still shows 01A1, please replace incline motor
.
- If auto calibration is finished, please follow the incline motor installation
SOP to fix incline motor.
c.
Replace LCB.
01A3 C Motor is disconnected T
a.
Check the connection of the motor cable at the MCB.
b. Check if the MCB LED DSP1 (MCU).
- If LED DSP1 is blinking or solid light, replace the motor
-
If LED DSP1 is not lit, replace the MCB.
01A8 C Main motor over current T
a.
Check the condition of the running deck and belt. Replace the belt and flip or
replace the running deck as needed.
b.
Replace the MCB.
01AC C
Electro magnet (ECB) over
current
HUR
a.
Check if the Electro-magnet is short circuited or open.
b. If the resistance data shows a short/open ohms or is outside the range of 12.8
~14.2 ohms, replace the Electro-magnet.
c. If the resistance data is in the range between 12.8 ~14.2 ohms, replace the LCB.
C
a.
On standby mode, measure the resistance on ECB1 and ECB2. Please check the
ECB extension cable connection at the LCB (pins 1 & 3 for ECB1, pins 2 & 4 for
ECB2), there should be between 12.8 ~ 14.2 ohms.
- If the ECB resistance is out of the range, replace the ECB.
-
If the ECB resistance is within the range, replace the LCB.
b.
Check the gap of ECB1 and ECB2. There should be a gap of .5mm between the
ECB and the flywheel.
01AF C
Electro magnet (ECB) dis
-
connected
HUR
a.
Check if the Electro-magnet is short circuited or open.
b. If the resistance data shows a short/open ohms or is outside the range of 12.8
~14.2 ohms, replace the Electro-magnet.
c. If the resistance data is in the range between 12.8 ~14.2 ohms, replace the LCB.
Resistance disconnect A
a.
Check if the resistance is short circuit.
- If resistance data is under 10 ohms, please replace power resistance.
-
If resistance data is over 10 ohms, please replace LCB.
Electro magnet (ECB) dis-
connected
C
a.
Check the connection of the ECB extension cable from the LCB to the ECB.
b.
Check to see if LED8 and LED10 on the LCB have a brief light for 3 second when
you power on machine.
-
If LED8 and LED10 do not have a brief light, replace the LCB.
-
If LED8 and LED10 do have a brief light, check the ECB
extension cable
connection at the LCB (pins 1 & 3 for ECB1, pins 2 & 4 for ECB2), there
should be between 12.8 ~ 14.2 ohms.
- If the ECB resistance is out of the range, replace the ECB.
c.
If the ECB resistance is within the range, replace the LCB.
01B4 C
Battery connection reverse
protection
AHUR
a.
Check the battery wire connection between the battery and LCB.
b. Check the battery voltage.
- If there is no data on voltage, replace the battery
.
- If there is data on voltage, replace the LCB.
014A
(01AE)
B
LCB charge current is
abnormal
AHUR
a.
Replace LCB.
0140 B Incline motor operation fail A
a.
Please run
Auto Calibration.
b. If the error code happens in Auto-calibration, the machine still can work, no need
to do anything.
c. If the error code happens in workout, please replace the incline motor
.
0141 B Motor over temperature T
a.
Check the connection of the motor cable at the MCB.
b. Use a multi-meter to check the motor wire circuit. Set the multi-meter to Ohms
and place both terminals on the blue wires of the motor cable.
-
If there is an Ohm reading above 0, replace the motor
.
-
If the Ohm reading is 0, replace the MCB.
0144 B Motor over current T
a.
Check the condition of the running deck and belt. Replace the belt and flip or
replace the running deck as needed.
b. Replace the MCB.

Matrix 7xe Specifications

General

Brand	Matrix
Model	7xe
Category	Music Mixer
Language	English