Pioneer CT-W530R User Manual

PLAYBACK
SINGLE PLAYBACK
(Using
only
one
deck,
either
deck
|
or
deck
I!)
1. Insert a recorded tape.
2. Set DOLBY NR switch (0.
3. Set REV MODE selector (.
{See page 8.)
4.
Set
the
stereo
amplifier
for
tape
playback.
5. Press the playback (> or €) button @.
@
Playback
can
be
performed
on
either
deck
|
or
deck
il,
only
one
ata
time.
@
Always
set
DOLBY
NR
switch
@
to
the
same
position
used
for
recording.
To
Momentarily
Stop
Playback
(Using
only
deck
H)
@ Press the pause (§%)} button @.
@
To
resume
playback,
press
the
pause
(fll)
button
@)
or
the
play-
back
(P
or
)
button
@.
When
Playback
is
Finished
5
Press
the
stop
(
@)
button
@@.
BLANK
SKIP
(Skipping unrecorded portions during playback)
Press
RELAY/SKIP
button
(1,
turning
the
corresponding
indicator
‘on,
In
this
mode,
when
an
unrecorded
portion
continues
for
more
than
15
seconds,
the
unit
will
fast-forward
the
tape
to
the
begin-
ning
of
the
next
recorded
position,
then
resume
playback
from
there.
OPERATION
OF
DECK
|
USING
A
REMOTE
CONTROL
UNIT
NOT
DESIGNED
FOR
DOUBLE
DECKS
(Not
on
European
model
of
CT-W630R)
[Operation of deck 1]
Perform
the
following
operation
when
turning
the
power
of
this
unit
on,
Turn
on
the
power
while
pressing
the
stop
(
Ml)
button
(®
for
deck
1.
Hotd
the
stop
(
™
}
button
(3
down
for
approximately
5
seconds,
Operation
of
deck
|
will
now
be
possible.
[Switching operation from deck | to deck I!)
With
deck
If
stopped,
press
the
deck
If
stop
(
if}
button
@.
Operation
of
deck
1! will
now
be
possible.
Operation
can
be
switched
back
to
deck
|
from
deck
Il
by
pressing,
the
stop
(
#)}
button
@®
of
deck
|
again
while
deck
|
is
stopped.
NOTE:
When
a
power
failure
or
another
sudden
change
in
power
supply
{caused
by
lighting,
etc.)
occurs
during
operation
of
the
unit,
it
will
be
reset
to
the
OFF
state.
To
restart
operation,
please
repeat
the
steps
described
above.
RELAY PLAYBACK
(Using both decks for continuous playback)
1. Insert recorded tapes in both decks.
2. Set DOLBY NR switch (©.
3. Set REV MODE selector (2.
{See page 8.}
Set the stereo amplifier for tape playback.
Press RELAY/SKIP button (1).
The [RELAY] indicator will light up.
Press
the
playback
{P
or
4)
button
(1)
of
the
deck
where
playback
is
to
start.
gp
2
To
Momentarily
Stop
Playback
(Using
only
deck
1)
@ Press the pause (HN) button @.
@
To
resume
playback,
press
the
pause
(##)
button
(
or
the
play
back (P or €) button @.
When Playback is Finished
Press the stop { @) button (@.
@
Continuous
playback
can
be
performed
either
from
deck
|
to
deck
It
or
from
deck
Il
to
deck
|.
@
For
relay
playback,
always
use
tapes
recorded
with
the
same
Dolby
NR
version,
and
set
DOLBY
NR
switch
@
to
the
same
position
used
for
recording.
@
When
playback
finishes
in
one
deck,
and
operation
stops
auto:
matically
at
the
tape
end,
the
other
deck
will
search
for
the
be-
ginning
of
the
first
selection
and
start
playback.
@
You
can
replace
tapes
already
listsended
to
during
playback
on
the
other
deck,
for
continuous
playback
of
different
tapes.
This
is
a
convenient
feature
for
party,
background
music,
etc.
®
if
mute
playback
continues
for
more
than
15
seconds
with
the
indicator
fit,
the
blank
skip
function
will
automatically
search
for
the
beginning
of
the
next
selection
and
resume
play
back
from
there,
To
cancel
relay
playback,
press
RELAY/SKIP
button
@
once
again
(turning
the
LRELAY
] indicator
off).
Differences
between
playback
direction
settings
dur-
ing
relay
playback
and
reverse
modes:
Tape play mode ]
at beginning of Reverse mode
playback
i
ne = |
— =a a)
Deck:
(|'Deck.tt
One-way
Two-way
Repeat
:
4
aa
>
>
FoF
FR-FR
FR-FRFR,.,
4
4
> I
FoR
FR-FR
FROFR“FR..,
ac
|
~<
>
RoE
R-FR
R+FROFR..
|
|
~<q
R—-R
RFR
R-FR-FR...
|
In
the
two-way
and
repeat
modes,
relay
playback
is
always
begun
from
the
forward
direction.
F; Forward playback R: Reverse playback
—: Relay playback
3
ARBIO058>

Pioneer CT-W530R Specifications

General

Brand	Pioneer
Model	CT-W530R
Category	Cassette Player
Language	English