Pioneer PD-101 User Manual

CONVENIENT OPERATION FOR RECORDING
meee
To
program
all
tracks
on
the
disc:
press
the
button
once
and
do
not
perform
step
2
below.
In about three seconds, the player will automatically select the
tape length (46, 60 or 90 minutes) which will allow recording of
all tracks on the disc, then program the tracks. |
Example: The tape playing time 46 minutes is selected.
COMPU PROGRAM EDIT AUT3 PROGRAM EDIT
Side A
2 Designate the length of tape to be used.
When the digit buttons are used:
Press the digit buttons to set the length (time) of the tape.
Press the 10's digit button and 1's digit button sequentially. (To
enter 9 minutes or less, press and then the corresponding
digit button.)
To confirm the programmed results:
After completion of .
Press
Ki
<4
of
BP
bP
to
set
the
length
(time)
of
the
tape.
P
programming,
press
COMPU/AUTO
EDIT;
When the track search buttons are used:
each time the button is pressed, the program results will be
@ Each time the buttons are pressed, the time setting will change alternately displayed for tape side A and B
in the following order:
46 + 54 «+> 60 <> 74 «<> 90 NOTES:
| | Unit: Minute e Up to 24 steps can be programmed.
@ With discs contained 24 tracks or more, programming may
not be correctly performed.
e if the selected time is too short for any track to be
programmed, programming cannot be performed.
e /f you wish to enter the time with the digit buttons after the
time is already entered with kid << of BR PPI in step 2.
press [>10]|. The digit buttons can now be operated.
@ If the disc ts in the player, the contents of the Compu program
edit are not cleared even when the power is turned off.
However, if the power is turned off with an audio timer or by
unplugging the power cord, the program contents will be
erased.
e The displayed time is memorized and the player starts
calculation by pressing COMPU/AUTO EDIT or if other time
setting is not selected within 3 seconds.
TROUBLESHOOTING
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check
the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being
used.
lf the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or your
dealer to carry out repair work.
Disc tray is not expelled when OPEN/ | @ Power plug is disconnected from outlet. e Connect plug to amplifier or wall outlet.
CLOSE is pressed. @ The POWER switch is OFF (STANDBY). @ Press the POWER switch ON.
s
When playback is started, it stops | e Disc is loaded upside down. @ Load the disc correctly with the label side UP.
immediately. Pauses or stops during | e Smudges etc., on the disc. e Clean the smudges from the disc and then play
playback. it again.
No sound Output cables are connected incorrectly or
loosely.
Incorrect operation of stereo amplifier.
Connect properly.
@ Check the settings of amplifier switches and
sound volume controls.
@ Clean away dirt.
@ Press the PLAY & button.
Pin plugs and/or amplifier terminals are dirty.
Player is in pause mode.
Sound is distorted, noise is output.
Incorrect connections, Connect to amplifier‘’s AUX or CD terminals.
Do not connect to PHONO terminals.
@ Clean away dirt.
@ Switch OFF TV set, or move player away from
TV set. :
e Pin plugs and/or amplifier terminals are dirty.
e Interference is being picked up from a TV
set.
11
<PRB1159>
En

Pioneer PD-101 Specifications

General

Brand	Pioneer
Model	PD-101
Category	CD Player
Language	English