46
> Specifications > Settings > Listening Modes > Playback Function > Basic Manual
Troubleshooting | Appendix
AV Adjust
You can quickly adjust settings you frequently use, such as
tone adjustments, etc.
Operation:
You can make the settings on the TV screen while playing
something. Press
on the remote controller to display
the AV Adjust menu. Note that there is no display on the TV
screen when the input selector is "CD", "TV", "PHONO",
"FM", or "AM", so follow the main unit's display while doing
the operations.
AV Adjust
Tone
Level
MCACC
Other
Bass
Treble
BD/DVD
Select the item with the cursor / buttons of the remote
controller and press ENTER to confirm your selection.
Use the cursors to change the settings.
•
To return to the previous screen, press .
•
To exit the settings, press .
■ Tone
Bass :
Enhance or moderate the bass range of the speaker.
Treble :
Enhance or moderate the treble range of the speaker.
•
It cannot be set if the listening mode is Direct or Pure
Direct.
■ Level
Center :
Adjust the speaker level of the center speaker while
listening to some sound.
Subwoofer 1 / Subwoofer 2 :
Adjust the speaker level of the subwoofer while listening to
some sound.
•
The adjustment you made will be reset to the previous
status when you turn the unit to standby mode.
■ MCACC
MCACC Memory :
From MCACC Memory 1 to 3 where speaker settings
calibrated with "Full Auto MCACC" or "Manual MCACC"
are saved, select which Memory to use.
MCACC EQ :
Enable or disable the equalizer function that corrects for
distortion caused by the acoustic environment of the room.
•
It cannot be set if the listening mode is Pure Direct.
Reflex Optimizer :
Enhance the reflection effect of Dolby enabled speakers
from the ceiling.
•
This setting can be selected when "System Setup" -
"Speaker" - "Configuration" - "Height 1 Speaker"/"Height
2 Speaker" is set to "Dolby Speaker".
•
It cannot be set if the listening mode is Pure Direct.
Standing Wave :
Select whether to enable or disable the standing wave
control calibrated in "MCACC Pro" - "Manual MCACC" -
"Standing Wave.
•
It cannot be set if the listening mode is Pure Direct.
Phase Control：
Correct phase disturbance in the low range to enhance
the bass. This enables you to achieve powerful bass
reproduction that is faithful to the original sound.
•
It cannot be set if the listening mode is Pure Direct.
When "Phase Control" is set to "Full Band":
Along with the Phase Control function, the Full Band
Phase Control function is also enabled. The Full Band
Phase Control function corrects for group delay (the
difference between phase and timing) between speakers
when speaker units are divided into multiple parts, such
as tweeter and woofer sections, and furthermore it lines
up the phases of the connected speakers so the unit can
achieve more accurate reproduction across the full range
(full band) and across all channels. Furthermore, if the
"Front Align" calibration type has been selected and Full
Auto MCACC was performed, the phases of speakers
other than the front speakers are corrected to match the
frequency phase characteristics of the front speakers.
•
"Full Band" cannot be selected if Full Auto MCACC has
not been performed.
Phase Control + :
Except for discs made according to the phase control
standard, the lower frequency range on discs is recorded
later than the other ranges. This adjusts the phase for
such discs. If you select "Auto", the polarity and correlation
is also detected and adjusted, not just the delay in low
frequency.
•
It cannot be set if the listening mode is Pure Direct.
LFE Mute Level :
Adjust the low-frequency effect (LFE) level for Dolby Digital
series, DTS series, Multichannel PCM, and DSD signals.
Theater Filter :
Adjust the soundtrack that was processed to enhance
its high pitch range, in order to make it suitable for home
theater. This function can be used in the following listening
To Next Page
Loading...
Need help?
General
Weight and Dimensions
