Home
Rittal
Control Unit
CMC III Processing Unit
Rittal CMC III Processing Unit Frequently Asked Questions
4
of 1
of 1 rating
24 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
FAQ
–
CM
C III
Page
5
of
24
Notes on these F
AQ
–
CMC I
II
These FAQs refer
to softw
are version V3.15.20_
10
of
the CMC
III. Some of the expl
anations
may vary
from older versions.
4
6
Table of Contents
Table of Contents
1
Table of Contents
2
Notes on These FAQ - CMC III
5
CMC III General
6
How Many Sensors Can be Connected to each CMC III Processing Unit and CMC III
6
Processing Unit Compact
6
What System Characteristics Does My Computer Need in Order to be Able to Operate the CMC III
6
Can I Represent Multiple CMC III Systems on a User Interface
6
How Can the CMC III Data be Included in Other Systems
6
Can the CMC III Data also be Transferred Via Bacnet or Modbus
6
Can the Messages from Several CMC III Systems be Sent Using a Single GSM/ISDN Unit
7
Is the 3124.200 Interface Card for Cooling Units with Comfort Controller Compatible to the CMC III
7
Modifications Need to be Made to the Firmware
7
Which SD Cards and USB Sticks Can be Used
7
Is It Possible to Connect a Camera to the CMC III
7
Which Data Encryption Standard Is Used for the Network Communication
8
CMC III Software Configuration
9
What Can be the Reason
9
After Selecting a Sensor and Clicking on "Alarm Configuration", no Values for Selection Are Listed in the Window. How Can I Rectify this
10
What Is the Difference between a "Virtual Device" and a "Task
11
How Many Messages Can the CMC III Store in the Logging
11
Can the Logging Messages be Deleted
11
Can a System Configuration be Saved and Recreated on Another Device
11
How Do I Save/Copy the Configuration of a CMC III System Onto Another System
12
Is It Possible to Copy a Company-Own Certificate to the CMC III for Encrypted Communication
12
The Login with Internet Explorer Is Not Possible Because the Buttons Are Inactive, Although if I Use the Newest Version. Which Configurations Should be Done
13
How Should a Management Software be Configured Regarding Encryption to Poll the CMC III over Snmpv3
15
If I Cannot See the Live Picture of the Axis Webcam, Although It Is Configured Correctly in the CMC III. What Should be Changed in the Software of the Webcam
15
Charts (Record of Measured Values)
17
Can I Save the Measurements from a CMC III System
17
At What Intervals Are Values Recorded in the System Memory
17
How Can I Display the Saved Values
17
What Happens if I Reboot the System
17
Can I Download and Edit the Measurements from the System
17
How Many Measurement Points in Total May be Stored in each File
17
Can Values be Added Retrospectively to a File
18
Installation and Wiring
19
The Infrared Sensors Do Not Detect the Door in Its Closed State, What Needs to be Considered
19
Interface Is Used
19
If the CMC III I/O Unit Is to be Connected with Several Fault-Message Contacts of a Device, How Must It be Wired
20
How, for Example, Is a Lamp Connected to the Relay Output
20
Door Control with CAN Bus Access
21
How Many Racks Can be Controlled with a CMC III System
21
How Many Reader Systems Must be Installed
21
Can a Reader System be Used to Release Selected Doors Only
21
How Many Cards or Number Codes Can be Stored in the System
22
Can a Number Code or a Transponder Card be Used to Open an External Lock, E.g. a Door Buzzer, or Activate a Magnet
22
What Card Standard Does the 7030.230 CMC III Transponder Reader Support
22
Can Other Card Types also be Integrated
22
Is It Possible to Release One or more Doors if Two Cards or Two Numerical Codes Are Used (4-Eyes Principle)
22
Can the Software be Set in such a Way that Users Need a Card and a Numerical Code
22
Flexibly Designable Web Interface (Dashboards) and Mobile Website
23
Following an Update, Why Are the "Dashboards" Tab and the Button on the Homepage no Longer Visible
23
Other manuals for Rittal CMC III Processing Unit
Installation Guide And Short User's Guide
18 pages
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Rittal CMC III Processing Unit and is the answer not in the manual?
Ask a question
Rittal CMC III Processing Unit Specifications
General
Brand
Rittal
Model
CMC III Processing Unit
Category
Control Unit
Language
English
Related product manuals
Rittal SK 5503.010
28 pages
Need help?
General
To Next Page
