Roland fp-30 User Manual

6
Adjusting the Brilliance (Brilliance)
Here’s how to adjust the brilliance of the sound (3 levels).
DEFAULT
C5
2
1
+
–
Hold down
Adjusting the Reverberation (Ambience)
You can adjust a reverberation of the sound, and get the impression that you are
performing in a concert hall (5 levels).
1
Hold down
DEFAULT
C5
2
+
–
Dividing the Keyboard in Two (Twin Piano)
You can divide the keyboard into left and right sections so that two people can
play the same pitch ranges. This function lets you use the unit as though it were
two pianos.
1
Hold down
C5
2
OFF
PAIR
INDIVIDUAL
The keyboard will be divided into left and right sections, with “middle C” located in
the center of each section.
You can choose one of the following ways in which the sound will be heard.
Value Explanation
PAIR
The sound will be heard from the right as you play toward the right of the
keyboard, and from the left as you play toward the left.
INDIVIDUAL
Notes played in the right area will be heard from the right speaker, and
notes played in the left area will be heard from the left speaker.
* The left and right sections will have the same tone (Piano). Twin Piano will be
cancelled when you push one of the TONE buttons.
* The damper pedal aects only the right section of the keyboard.
* The soft pedal operates as the damper pedal for the left section of the
keyboard (when using the KPD-70).
Changing the Pitch of the Tone in Octave Steps (Octave Shift)
When using Dual Play (p. 2) or Split Play (p. 2), you can change the pitch of each
part (PIANO, E. PIANO, OTHER) in steps of an octave. This is called the “Octave
Shift” function.
Hold down
Press one
C4
2
-1 0 +2
+1-2
1
Disabling the Buttons (Panel Lock)
While holding down the [PIANO] button, turn the power on. Keep holding down
[PIANO] button for at least six seconds. Panel Lock is engaged, and buttons other
than the [
L
] (Power) button and the Volume buttons are disabled. This prevents
the tones or settings from being changed if you inadvertently press a button.
Panel Lock will be cancelled when you turn o the power.
Saving the Settings (Memory Backup)
When this unit’s power is turned o, it will return to its default settings. However, if
desired, you can save the following settings so that they will be remembered even
after the power is o. This is called the “Memory Backup” function.
Settings saved by Memory Backup Page
Key Touch p. 7
Brilliance p. 6
Ambience p. 6
Master Tuning p. 7
Bluetooth ON, OFF p. 7
Bluetooth MIDI, Turns pages. p. 7
Bluetooth Mode1, Mode2 p. 7
1. Hold down the [FUNCTION] button and press the [
t
] button.
The [
s
] button and the [
t
] button will blink.
If you decide to cancel, press the [
s
] button.
2. To save the settings, press the [
t
] button.
When all the LEDs on the buttons are lit, the operation is complete.
Formatting a USB Flash Drive
Here’s how to initialize (format) the entire contents saved on a USB ash drive.
NOTE
5 Formatting will erase everything that has been saved on the USB
ash drive.
5 Before using a new USB ash drive with the FP-30 for the rst time, you
must format the USB ash drive.
1. Connect the USB ash drive that you want to format to the USB MEMORY port.
2. While holding down the [
s
] button, turn the power on. Keep holding down [
s
]
button for at least six seconds.
The [
s
] button and the [
t
] button will blink.
If you decide to cancel, press the [
s
] button.
3. To execute the format, press the [
t
] button.
When all the LEDs on the buttons are lit, the operation is complete.
4. Turn the power o, then on again.
Restoring the Factory Settings (Factory Reset)
The settings you’ve changed in the function mode can be restored to their factory-
set condition.
NOTE
When you execute a factory reset, all settings will be initialized and the song you
recorded in internal memory will be erased.
1. While holding down the [FUNCTION] button, turn the power on. Keep holding down
[FUNCTION] button for at least six seconds.
The [
s
] button and the [
t
] button will blink.
If you decide to cancel, press the [
s
] button.
2. To execute the Factory Reset, press the [
t
] button.
When all the LEDs on the buttons are lit, the operation is complete.
3. Turn the power o, then on again.
Advanced Features

Roland fp-30 Specifications

General

Certification	FCC, CE
Sound effects	Ambience, Brilliance
Tones quantity	35
Pedals quantity	1
RMS rated power	24 W
Speaker diameter	120 mm
Number of speakers	2
Metronome tempo range	20 - 250 bpm
Metronome beats per bar	0, 2, 3, 4, 5
Maximum polyphony (notes)	128
Bluetooth version	4.0
USB connector type	USB Type-A, USB Type-B
Headphone connectivity	3.5 mm
AC input voltage	100 - 240 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (max)	22 W
Power consumption (min)	3 W
Built-in display	No
Country of origin	Malaysia
Tuning frequency	415.3 - 466.2 Hz
Demo songs quantity	30
Transposition range	-6 - 5 octave(s)
Sound pressure level	120 dB
Product color	White
Keys quantity	88 keys
Number of keyboard sensitivity levels	5

Weight and Dimensions

Depth	284 mm
Width	1300 mm
Height	150 mm
Weight	14100 g