Scheppach DP16VLS User Manual

www.scheppach.com
28
|
GB
Adjusting table height (Fig. 11)
1. Loosen the table support lock handle (E).
2. Adjust the table (3) to the desired height.
3. Re-tighten the table locking (E).
4. Note: It is better to lock the table to the column in a
position so that the tip of the drill bit is just slightly
above the top of the workpiece.
Choosing speed and tensioning belt (Fig. 12)
Note! Pull power plug!
You can set di󰀨erent spindle speeds on your pillar drill-
ing machine:
1. Once you have switched o󰀨 the device, you can
open the belt guard (11). Loosen the screw (V) and
open the belt guard (11). All adjustment options for
the spindle speed are available in the machine’s
belt guard (11)
2. Loosen the drive belt on the right side of the ma-
chine head by unfastening the locking nuts (12) on
both sides. Pull the right side of the motor in the di-
rection of the spindle to loosen the v-belt. Tighten
the counternuts again (12).
3. Attach the v-belt to the corresponding belt pulleys.
The belt must always run straight.
4. Loosen the counternuts (12) and press the right
side of the engine back, in order to tension the
V-belt again.
5. Tighten the counternuts again (12). Belt should de-
ect approximately 13 mm –1/2“ -by thumb pres-
sure at mid-point of belt between pulleys.
6. Close the belt guard (11).
7. If belt slips while drilling readjust belt tension.
Tip: Safety switch
If you wish to set the speed, you must open the belt
guard (11). The device switches o󰀨 immediately to
avoid the risk of injuries.
Removing the chuck
Open jaws of chuck as wide as they go by turning
chuck sleeve anticlockwise.
Carefully tap chuck with mallet in one hand while hold-
ing chuck in other hand to prevent dropping it when re-
leased from spindle nose.
Installing the chuck (Fig. 8)
1. Clean the conical hole in the chuck (5) and the
spindle cone with a clean piece of fabric. Make
sure there are no foreign particles sticking to the
surfaces. The slightest piece of dirt on any of
these surfaces will prevent the chuck from seating
properly. This will cause the drill bit to wobble“. If
tapered hole in the chuck is extremely dirty, use a
cleaning solvent on the clean cloth.
2. Push the chuck up on the spindle nose as far as
it wiII go.
3. Turn chuck sleeve clockwise (when viewed from
above) and open jaws in chuck completely.
4. Place a piece of wood on the machine table and
lower the spindle onto the piece of wood. Press
rmly to ensure that the food sits exactly.
Installing laser module (Fig. 15, 16)
Fasten the laser module (13) with the countersunk
screw (U) onto the machine head (4) as shown in the
gures.
Make sure the plastic pin on the laser module sits in the
hole without thread.
Fastening radial drill press to supporting surface
For your own safety, screw connection on a workbench
or similar is strongly recommended.
m Warning:
All the necessary adjustments for the good working of
your drill press have been done at the factory. Please
do not modify them.
However, because of a normal wear and tear of your
tool, some readjustments might be necessary.
9. Operation
m Warning:
If you are not familiar with this kind of machine, take
advice from an experimented person. In any case you
should have read and understood the safety and op-
erational instruction before attempting to operate this
product.
Pivoting the table (Fig. 10)
1. To bring the table (3) to the inclined position, re-
lease the table locking (S) and adjust the desired
table angle.
2. Re-tighten the table locking.

Scheppach DP16VLS Specifications

General

Drilling	Yes
Screwdriving	-
Product color	Blue, Grey
Input power	500 W
Power source	AC
AC input voltage	230 - 240 V
AC input frequency	50 Hz
Idle speed (max)	- RPM
Chuck capacity (max)	16 mm
Drilling diameter in steel (max)	- mm
Product type	Bench drill press
Housing material	Steel
Drill table size (WxD)	160 x 160 mm

Weight and Dimensions

Depth	460 mm
Width	380 mm
Height	250 mm
Weight	15420 g