16
2
1
3
2
1
3
1. Raise the needle to its highest position by rotating the
hand wheel toward you (counter-clockwise).
2. Open the bobbin access cover by pulling it down.
With your fingers, pull open the bobbin case latch as
shown, and take out the bobbin case from the shuttle.
3. Release the latch, and bobbin will drop out of the case.
1. Hold the bobbin in your right hand with the thread
running clockwise.
2. Insert the bobbin into the case with about 4” (10 cm) of
thread showing outside the case.
3. Pull the thread through the slit in the case and then
XQGHUQHDWKWKHÀDWWHQVLRQVSULQJ,WZLOOFOLFNZKHQLWLV
in place.
4. Keep about 4” (10 cm) of thread showing outside the
case.
REMOVING BOBBIN CASE FROM SHUTTLE
ǽȓȞȓȐȓȒȖȠȓȖȑșȡȐȘȞȎȗțȓȓȐȓȞȣțȓȓȝȜșȜȔȓțȖȓ
ȝȜȐȓȞțȡȐȚȎȣȜȐȖȘțȎȟȓȏȭȝȞȜȠȖȐȥȎȟȜȐȜȗ
ȟȠȞȓșȘȖ
ǼȠȘȞȜȗȠȓȘȞȩȦȘȡȦȝȡșȪțȜȑȜȜȠȟȓȘȎȝȜȠȭțȡȐȓȓ
ȐțȖȕǼȠȘȞȜȗȠȓȕȎȧȓșȘȡȦȝȡșȪțȜȑȜȘȜșȝȎȥȘȎȘȎȘ
ȝȜȘȎȕȎțȜțȎȞȖȟȡțȘȓȖȐȩțȪȠȓȦȝȡșȪțȩȗȘȜșȝȎȥȓȘ
ȖȕȥȓșțȜȘȎ
ǼȠȝȡȟȠȖȠȓȕȎȧȓșȘȡȖȦȝȡșȪȘȎȐȩȝȎȒȓȠȖȕȘȜșȝȎȥȘȎ
ǶǵǰǹdzȅdzǻǶdzȆǽȁǹȊǻǼDZǼǸǼǹǽǮȅǸǮ
ǶǵȅdzǹǻǼǸǮ
9RODQÕNHQGLQL]HGR÷UXVDDWLQWHUVL\|QQGHoHYLUHUHNL÷QH\L
HQ\NVHNSR]LV\RQDNDOGÕUÕQ
$úD÷ÕGR÷UXoHNHUHNPDVXUDHULúLPNDSD÷ÕQÕDoÕQ
3DUPDNODUÕQÕ]ODPHNLNPDQGDOÕQÕJ|VWHULOGL÷LJLELoHNHUHN
DoÕQYHPHNL÷L\XYDVÕQGDQoÕNDUÕQ
0DQGDOÕEÕUDNÕQYHPDVXUDPHNLNWHQoÕNDFDNWÕU
0(.øöø1<89$6,1'$1d,.$5,/0$6,
INSERTING BOBBIN INTO BOBBIN CASE
ǰȜȕȪȚȖȠȓȦȝȡșȪȘȡȐȝȞȎȐȡȬȞȡȘȡȠȎȘȥȠȜȏȩțȖȠȪ
ȐȩȣȜȒȖșȎȝȜȥȎȟȜȐȜȗȟȠȞȓșȘȓ
ǼȠȚȜȠȎȗȠȓȟțȎȝȜșțȓțțȜȗȦȝȡșȪȘȖțȖȠȪȒșȖțȜȗ
ȁǿȀǮǻǼǰǸǮȆǽȁǹȊǸǶǰȆǽȁǹȊǻȉǷ
ǸǼǹǽǮȅǼǸ
øSOLNVDDW\|QQGHDNDFDNúHNLOGHPDVXUD\ÕVD÷HOLQL]OHWXWXQ
0DVXUD\ÕLSOL÷LQFPNDGDUÕGÕúDUÕGDNDODFDNúHNLOGHPHNL÷H\HUOHúWLULQ
øSOL÷LPHNLNWHNL NDQDOGDQoHNLQ YHGDKD VRQUDG] WDQVL\RQ\D\ÕQÕQ DOWÕQGDQJHoLULQ 0DVXUD
\HULQHRWXUDFDNWÕU
øSOL÷LQFPNDGDUÕQÕPHNL÷LQGÕúÕQGDEÕUDNÕQ
0$685$1,10(.øö(7$.,/0$6,
ȜȘȜșȜȟȚȖȐȟȠȎȐȪȠȓȦȝȡșȪȘȡȐȘȜșȝȎȥȓȘ
ǽȞȜȐȓȒȖȠȓțȖȠȪȥȓȞȓȕȧȓșȪȐȘȜșȝȎȥȘȓȎȕȎȠȓȚȝȜȒȝșȜȟȘȜȗȝȞȡȔȖțȜȗǼțȎ
ȧȓșȘțȓȠȘȜȑȒȎȐȟȠȎțȓȠțȎȚȓȟȠȜ
ǽȞȜȐȓȞȪȠȓȥȠȜȏȩȖȕȦȝȡșȪȘȖȐȩȣȜȒȖșȜȜȘȜșȜȟȚțȖȠȖ
To Next Page
Loading...
Need help?
General
