Sony VPL-FHZ65 User Manual

33
The Connection/Power Menu
The Connection/Power menu is used for setting for the connections and power.
Setting items Description
Network Setting
IPv4 Setting
IP Address Setup Auto(DHCP): The IP address is assigned automatically from the
DHCP server such as a router.
Manual: To specify the IP Address manually.
IP Address/ Subnet
Mask/ Default
Gateway/Primary
DNS/Secondary
DNS
When “Manual” is selected for “IP Address Setup,” select the item
with the B or b key and input the value with V or v key. When all
items are entered, select “Apply” then press the ENTER key. The
entered settings will be registered.
IPv6 Information Displays the IPv6 address information.
When setting the address of IPv6, set it from the browser (page 42).
HDBaseT Settings
LAN Setting via HDBaseT/LAN Port: You can select either via the LAN of the
HDBaseT equipment connected to the HDBaseT teminal or via the
network connection with the LAN terminal of the main unit.
*1 *2
RS-232C Setting
*3
via HDBaseT: You can connect this unit to the RS-232C terminal via
the HDBaseT transmitter. (Baud rate: 9,600 bps)
RS-232C: Use when connecting to the RS-232C terminal of this unit
directly.
Dynamic Range
*4
Sets the image input level of the INPUT B/C/D terminal.
Auto: Distinguishes the image input level automatically.
Limited: Set when the image input level is 16-235.
Full: Set when the image input level is 0-255.
HDMI Cable Long/Normal: Select “Long” when the image is disturbed or not
projected.
Input-A Signal Sel. Auto/Computer/Video GBR/Component: When set to “Auto,”
selects the type of video signal input automatically when “Input-A” is
selected with the INPUT key.
*5
Color System Auto/NTSC3.58/PAL/SECAM/NTSC4.43/PAL-M/PAL-N: When set
to “Auto,” selects the color system automatically when “Video” is
selected with the INPUT key.
*5
ECO
Auto Power Saving
With No Input Light Cutoff: The light turns off automatically and power
consumption is reduced if no signal is input for about two minutes.
The light turns on again when a signal is input or any key is pressed. In
Light Cutoff, the ON/STANDBY indicator lights in orange. (page 46)
Standby
*6
: If no signal is input to the unit for about two minutes, the
power turns off automatically, and the unit enters standby mode.
Off: The “With No Input” function is disabled.

Sony VPL-FHZ65 Specifications

General

Matrix size	0.76 \
Native aspect ratio	16:10
Projection distance	- m
Projection technology	3LCD
Supported aspect ratios	-
Contrast ratio (typical)	10000:1
Screen size compatibility	40 - 600 \
Projector native resolution	WUXGA (1920x1200)
Keystone correction, horizontal	30 °
Focus	Auto
Throw ratio	1.39 - 2.23:1
Zoom capability	Yes
Focal length range	- mm
Service life of light source	20000 h
3D	No
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC 3.58, NTSC 4.43, PAL, PAL 60, PAL M, PAL N, SECAM
Supported graphics resolutions	1920 x 1200 (WUXGA)
Serial interface type	RS-232C
USB 2.0 ports quantity	0
Noise level	28 dB
Placement	Desktop
Product type	Large venue projector
Product color	White
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.5 W
Power consumption (typical)	509 W
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	10 - 90 %
Operating relative humidity (H-H)	20 - 80 %
Remote control type	Wired

Weight and Dimensions

Depth	515 mm
Width	460 mm
Height	169 mm
Weight	16000 g