24
Emptying solution
The disposal of solution must be carried out in accordance with the national
regulations.
Emptying procedures for the Foam Generator are explained in their own
instructions of use.
Cleaning the tool
Cleaning the pad
Cleaning the machine
Storing the machine
Service, maintenance and care
The correct maintenance of the machine is a precondition for error-free
operation and a long service life.
Service intervals
TASKI machines are high quality machines that have been checked for safety
at the factory by authorised inspectors. Electrical and mechanical components
are subject to wear and/or ageing after longer periods of use.
Service centre
Should you contact us due to a malfunction or for placing an order, please
always state the type, description and the serial number of your machine.
You can find this information on the name plate of your machine, and the
address of your nearest TASKI partner can be found on the last page of this
manual.
Malfunctions
Transport
Ensure that the machine is firmly lashed down and secured in the transport
vehicle.
Disposal
After becoming no longer fit for use, the machine and its accessories must be
disposed of in the correct manner in accordance with the national regulations.
On request, your TASKI partner can assist you with this.
• Remove the water tank from the machine and empty it.
• Empty the solution from the spray unit.
• Clean the tool under running water with a brush.
• Rinse out the spray unit thoroughly with warm water.
If the cleaning solution dries up, it could cause blockages.
• Lay the pad into cleaning solution for a few hours and then rinse it off.
The pads may be put into the washing machine and washed at a max. of
40°C.
• Air dry the pads.
Caution:
Do not tumble dry the pads!
Caution:
Never clean the machine with high water pressure or a water
hose.
The ingress of water into the machine might cause considerable
damage to mechanical or electrical parts.
• Wipe down the machine with a damp cloth.
Caution:
Never store the machine with a mounted tool!
The tool may get damaged and become unusable.
Caution:
Always unplug the mains plug from the main socket when carrying
out any maintenance work!
Caution:
Only TASKI branded spare parts must be used, otherwise
warranties and liabilities will be omitted!
Symbols:
◊ = after use, ◊◊ = every week, ◊◊◊ = every month
Activity ◊◊◊◊◊◊ page
Check the motor ventilation for the collection of
dust and clean when necessary
22
Empty spray unit and clean with warm water
23
Clean the brushes
24
Clean the pads and let them dry
24
Clean the machine with a damp cloth
24
• In order to maintain operational reliability and availability for use, the service
must be carried out after 250 working hours or at least once a year.
Shorter intervals are necessary in case of rough environments or special
conditions of use and/or inadequate maintenance.
Malfunction Possible causes Troubleshooting page
Machine does not
run
No power supply
• Insert the plug into the
mains socket
Guide pillar in upright
position
• Place the machine in
the working position
22
Safety switch defect
• Call your Service
Partner
22
Machine cannot
be operated, but
the on light
shows
Machine has
overheated causing
motor protection
switch (trip) to cut in.
• Wait a while, try again
(the protection switch
will automatically
reset)
Tool does not
rotate
Motor runs but not
tool
• Drive belt is torn or
lose
• Call your Service
Partner
Machine does not
reach rated
speed, motor
protection cuts in
Machine is
overloaded
• Check that you are
using the correct
working technique
23
Insufficient voltage,
power cord is too long
• Remove extention
• Check power supply
voltage
Machine runs
uneasy
Tool deformed or
damaged
•Replace
Spray pump is
working, cleaning
solution is not
coming out
Cleaning solution has
dried up in spray unit
or tube is blocked
• Clean spray unit
•Replace
• Remove the tool (refer to Page 23).
• Pull the height adjustment lever and fold the
guide pillar towards the front.
• Let go of the height adjustment lever, the guide
pillar will locate into place and stay at that angle.
• To lift the machine, one person must hold the tool unit and the other person
must hold the machine handle.
Caution:
The machine must always be carried by two persons and should
only be lifted by a single person in cases of emergency!
To Next Page
Loading...
Need help?
General
