17
Chapter 4 Menu Operation
Wireless settings:
To connect your TV to your network wirelessly, you need
a wireless router or modem and a wireless LAN adapter.
Note: If your TV doesn’t have an in-built wireless
Adapter, then
you need a
wireless USB dongle (which
is sold separately)
. Connect
the USB dongle to your
TV’s USB port.
Select
Settings >
Network, then select Wireless
settings to connect to a wireless network. you can set
up the wireless network connection accordingly.
WiFi switch: Select WiFi switch and press OK/► to
enter, use ▲/▼ to set it to On, then below options are
available. Otherwise, they are hided.
Scan: Select Wireless settings > Scan, then press
OK/►, the TV will scan all access points within
range. The access points found by the TV will be
displayed. Select an available access point, then
press OK to connect the TV to it.
Notes:
-
If you select a protected access point, you will
have
to enter the corresponding password. Press
OK
on
the remote control to display virtual
keyboard to enable you to enter it.
- This set has a memory function of available access
points, which enables your set to be connected to the
network even if you switch on TV after power off.
Manual:
Select Wireless settings > Manual, then
press
OK/►
, you will be prompted to enter the correct
SSID of an available wireless router to set up the
connection.
Wi-Fi Direct:
Select Wireless settings >
Wi-Fi Direct,
then press
OK/►
to enter, you can do Wi-Fi direct
password setting and change the password here.
Information:
Select Wireless settings >
Information
,
then press
OK/►
toenter,youwillndtheinformation
about WiFi status, etc.
System
Select Settings > System, then the System menu
appears on the right with the following options. Press
OK/►to enter and use ▲/▼ to choose an option.
Language: Press OK/►todisplaythelanguagelistand
use▲/▼toselectalanguage.
Timer: The Timer menu allows you to set the time zone
on your TV set, to program an automatic turn-off or
wake-up timer and to view the calendar.
Select System > Timer and press OK/► to confirm.
The Timer options are as below:
Time zone: Use ▲/▼to select the local time zone.
Clock: Press OK/► to display its options:
- Synchronization: Use ▲/▼to select Auto or
Manual. If Auto is selected, the TV will get the
time automatically from DTV signals, and the Time
item cannot be adjusted. If you select Manual, you
should set date and time at Date and Time item.
Highlight
Date or Time, press
OK
to enter and then
use
▲/▼/◄/►andOK buttons to change
the date
or time
.
Note: If Manual is selected, the time set in Time
option will not be memorized when turning on the
TV next time, and the TV 's time will start from the
default.
- Power on timer: Use ▲/▼ to select Once, Daily
or Off. If you select Once or Daily, you should set a
time period after which the TV automatically switches
to on at Time below this item. Highlight Time,
press
OK
to enter and then use
▲/▼/◄/►andOK buttons
to change
the time
.
- Power on Channel: Press OK/► to display its
submenu. Highlight Select mode, use ► to select
Last status, the power on channel will be the last
channel you watched before power-off. Or you can
select User select, then press ▲/▼ to select the
channel you want to watch when the TV is turned on
automatically next time, and press OKtoconrm.
- Power off timer: Use ▲/▼to select Once, Daily
or Off. If you select Once or Daily, you should set a
time period after which the TV automatically switches
to off at Time below this item. Highlight Time,
press
OK
to enter and then use
▲/▼/◄/►andOK buttons
to change
the time
.
Sleep timer: Sets a period of time after which the
TV set goes into standby mode. Use ▲/▼ to set
the period (120 minutes maximum). To disable this
function, select Off.
Auto standby: Sets a period of time after which the
TV set goes into standby mode. Use ▲/▼ to select
the period: 4 Hours, 6 Hours and 8 Hours. To disable
this function, select Off.
Lock: This menu can control the special function for TV
channels.
Note: You must enter your personal code before
entering the Lock menu.
Select System > Lock and press OK/►toconrm.
Then press the number buttons to enter the password to
enter the Lock menu. The factory default code is 1234.
And the super password is 0423. If you forget your
code, enter it to override any existing codes.
The Lock options are as below:
- Channel lock: This option allows you to lock a
certain Channel. Press OK/► to display Channel
lock menu, then use ▲/▼ to select a certain TV
channel you want to lock, then press OK to lock. To
unlock, use the same operation.
- Parental rating: This option allows you to set a
rating to a program. Highlight Parental rating, press
To Next Page
Loading...
Need help?
General
