Tektronix TDS2001C User Manual

Specifications
Table 1-1: Signal acquisition system characteristics (cont.)
Characteristic
Description
DC Voltage
Measurement Accuracy,
Average Acquisition
Mode
Vertical position = 0: ±(3% of |reading| + 0.1 div + 1 mV)
Vertical position ≠ 0 and vertical scale = 2 m V/div to 200 mV/div: ±[3% of |reading + vertical
position| + 1% of |vertical position| + 0 . 2 div + 7 mV]
Vertical position ≠ 0 and vertical scale > 200 mV/div: ±[3% of |reading + vertical position| + 1% of
|vertical position| + 0.2 div + 175 mV]
Delta volts between any two averages of 16 waveforms acquired under the same setup and ambient
conditions.
Delta Volts Measurement
Accuracy, Average
Acquisition Mode
(3% of |reading| + 0.05 div)
Analog Bandwidth
Defined in Section 4.6 of IEEE std 1057. The difference between the upper and lower frequencies, at
which the amplitude response, as seen in the data record, is 0.707 (-3 dB) of the response seen in the
data record at the specified reference frequency. Specifies only the -3 dB point. It does not include
the in-band response.
This is analog bandwidth when the instrument is DC coupled in sample or average mode. V/div values
are accurate for probe attenuation settings of 1X. No probe should be installed for these measurements.
System bandwidth is type tested to be equivalent to this specification with the provided probe in 10X
mode. Use Section 4.6.1 of IEEE 1057, with the reference frequency of 1 kHz at an amplitude of
5 divisions, driven from a 50 Ω source with external termination at the input BNC (25 Ω effective source).
TDS2022C, TDS2024C:
to ≥ 200 MHz for 5 mV/div through 5 V/div settings with bandwidth limit at full with temperature between
0°C and 35 °C. DC to > 160 MHz for 5 mV/div through 5 V /div settings with bandwidth limit at full for
temperatures between 0 °C and 50 °C. < 5 mV/div settings are limited to 20 MHz bandwidth.
TDS2012C, TDS2014C:
DC to ≥ 100 MHz for 5 mV/div through 5 V/div settings with bandwidth limit at full. < 5 mV/div settings
are limited to 20 MHz bandwidth.
TDS2002C, TDS2004C:
DC to ≥ 70 MHz for 5 mV/div through 5 V/div settings with the bandwidth limit at full. < 5 MV/div settings
are limited to 20 MHz bandwidth.
√ Analog Bandwidth,
DC Coupled, Sample or
Average
TDS2001C:
DC to ≥ 50 MHz for 5 mV/div through 5 V/div settings with the bandwidth limit at full. < 5 mV/div settings
are limited to 20 MHz bandwidth.
This is the analog bandwidth when the instrument is DC coupled. V/div values are accurate for probe
attenuation settings of 1X. No probe should be installed for these measurements.
TDS2012C, TDS2014C, TDS2022C, TDS2024C:
DC to ≥ 75 MHz for 5 mV/div through 5 V/div settings with the bandwidth limit at full. Settings less
than 5 mV/div are limited to 20 MHz bandwidth.
TDS2002C, TDS2004C:
DC to ≥ 50 MHz for 5 mV/div through 5 V/div settings with the bandwidth limit at full. Settings less
than 5 mV/div are limited to 20 MHz bandwidth.
Analog Bandwidth, DC
Coupled, Peak Detect,
typical
TDS2001C:
DC to ≥ 30 MHz for 5 mV/div through 5 V/div settings with the bandwidth limit at full. Settings less
than 5 mV/div are limited to 20 MHz bandwidth.
Analog Bandwidth
Selections
20 MHz bandwidth limit ON/OFF
TDS2000C Series Oscilloscope Service Manual 1–3

Tektronix TDS2001C Specifications

General

Brand	Tektronix
Model	TDS2001C
Category	Oscilloscope
Language	English