Teldat 4Ge User Manual

digits (e.g. the ‘&’ character would be %26). Thus, to enter an apn equal to access&network.es you can enter
apn=access%26network.es.
• Some parameters have a shortened version. For instance, the short version for password is pwd.
The first word contained in option 43 should be “antenna”. Since the device accepts the address offered by the
router, if you don’t enter this word the Teldat 4Ge won’t accept said address.
The configuration parameters available for the Teldat 4Ge are:
• “ pin=NNNN ”, allows you to configure the PIN number for the SIM card used in the Teldat 4Ge.
• “ apn= ”, configures the APN in the 4G network to which the Teldat 4Ge is going to be connected to.
• “ apntype= ”, or “ type= ” configures the APN type in the 4G network to which the Teldat 4Ge is going to be con-
nected to. It can be ipv4v6 or ipv6. If it is not configured by default, it will be ip (for IPV4 APNs).
• “ user= ”, or “ usr= ” allows the user to be configured so that it authenticates in the mobile operator’s APN.
• “ password= ”, or “ pwd= ”allows the password to be configured so that it authenticates in the mobile operator’s
APN.
• “ rxtimeout=T ”, or “ rxto=T ”, indicates that the transmission and reception packets are monitored. After T
seconds, if a response to a transmitted packet hasn’t been received, connections with the router and the access
module for the WWAN network are restarted. You can configure a value between 10 and 86399 seconds. This
parameter is deactivated by default.
• “ flowcontrol=N ”, or “ flow=N ”, indicates that the transmission and reception packets are monitored. After N
transmitted packets, if nothing has been received, connections with the router and the access module for the
WWAN network are restarted. You can configure a value between 1 and 65535 packets. This parameter is deactiv-
ated by default.
• “ ntpserver=AAA.BBB.CCC.DDD ” , or “ ntps=AAA.BBB.CCC.DDD ” , NTP server IP address used to syn-
chronize the device.
• “ ntpoffset=N ”, or “ ntpo=N ”, the time is expressed in GMT + ntpoffset. Default value is 2 (i.e. GMT + 2). Accept-
able values range from -12 to +12, in 1-hour intervals.
• “ mode= ”, helps select the technology that should be used to connect to the mobile network. This value can be
one of auto, gprs , wcdma , gprsp , wcdmap , lte , cdma , hrpd or hybrid . The gprsp and wcdmap modes indic-
ate that the technology used should preferably be GPRS or WCDMA. The default value is auto .
• “ domain= ”, or “ dmn= ”, allows the user to select the domain that the device will connect to. This value can be
cs , ps , cs+ps . Since voice call support is not yet implemented, we recommend using the ps domain. The default
domain is ps .
• “ idletime=T ” , or “ idle=T ”, configures the idle time (in seconds) for the 4G network session. If, when the ses-
sion is established, this timer times out before receiving a new packet from the router, the Teldat 4Ge considers
the session to be down and drops it. Acceptable values range from 0 to 65535 seconds. This parameter is not con-
figured by default (equivalent to having a value 0).
• “ atafterpin= ”, or “ aft= ”, or “ beforepin= ”, or “ bef= ”, allows the user to configure an additional AT command
that is sent during the 4G module's startup. It is generally used to send a certain network or modem parameter.
• “ coveragetimer=N ”, or “ ct=N ”, configures the sample period for the 4G network coverage values (Rx_level,
RSCP and EcIo). The N value is between 10 and 255 seconds. It is 60 seconds by default.
• “ clientid=no ”, or “ cid=no ” deactivates the client identifier that sends in the DHCP petitions. This is for configur-
ations with various Teldat 4Ge devices and Cisco routers.
• “ regdenied=1 ” , or “ regd=1 ”, activates the feature that switches off the 4G module radio interface for 5 seconds
in cases where the network initially denies registration (registration DENIED). This means you can avoid this state
and the module can be re-registered in the 4G network.
• “ pnum=N ”, or “ profilenum=N ”, selects the calling profile that the ESR-WWAN-ENABLER will use to make the
data call. This will allow you to select the calling profile of modules that make OTA ( Over The Air) APN provisioning
(i.e., without having to add an APN in the configuration). It admits values that range from 1 to 12.
• “ auth= ” , if the data APN requires authentication, this parameter allows you to select its type. This can be chap ,
pap or none if no authentication is required. If this parameter is not included, the authentication is pap by default.
• “ regapn= ”, or “ rapn= ” configures the registration APN of the 4G network that the Teldat 4Ge is going to be re-
gistered in. If the registration APN and the data APN are the same, we recommend using "reagapn=" and
"pnum=1".
• “ regapntype= ”, or “ rtype= ” configures the registration APN type in the 4G network where the Teldat 4Ge is go-
Teldat S.A.
3 Configuration
Teldat 4Ge 9

Teldat 4Ge Specifications

General

Brand	Teldat
Model	4Ge
Category	Network Router
Language	English