Vox MINI GO 3 User Manual

VOCODER does not produce sound unless data is input to both MIC IN and INPUT.
The amp doesn’t seem very loud
Is your guitar turned up?
Is the top panel VOLUME or GAIN knob turned down low?
Are you using a mobile battery?
Use a mobile battery with an output of at least 1.5A. Depending on the mobile battery or USB Type-C used, the power may not be turned on, or
the battery may not be able to provide sufficient power.
The rhythm sound is not output
Is the rhythm section LEVEL knob set to a low value?
Did you switch the mute on by operating the footswitch?
The rhythm tempo changes arbitrarily.
Are you using the rhythm simultaneously with the looper?
If the rhythm is played back during loop playback, the rhythm tempo is automatically set based on the rhythm tempo before playback and the length of the
recorded phrase.
Looper recording is not possible.
Are you trying to record a rhythm or an input from AUX IN?
The rhythm sound and the input from AUX IN are not recorded in the looper.
There’s no looper playback sound.
Is the LOOP LEVEL knob set to a small value?
Is footswitch operation muted?
Was the GAIN knob or VOLUME knob reduced during looper recording?
No sound is output from the microphone connected to the MIC IN terminal.
Is the microphone connected correctly?
Is the microphone switch turned off?
Is the TRIM knob set to a small value?
Is the amplifier model VOCODER selected with the microphone connected to MIC IN?
VOCODER does not produce sound unless data is input to both MIC IN and INPUT.
No effect is applied.
Is the tuner function turned on?
When the tuner function is turned on, Effect 1 is bypassed. Press the VARIATION button to turn the tuner off.
Is the EFFECTS knob set to the OFF position or a small value?
If Effect 2 is not applied to the microphone, is the SEND knob set to a small value?
Did you turn the effect off by operating the footswitch?
The function of the footswitch changes arbitrarily.
Are you operating the top panel while pressing the footswitch?
Operate the top panel and foot switch separately, except when changing the footswitch function.
(TIP) To prevent a function from being changed unintentionally, you can disable the function change operation during normal operation (refer to
“Foot Switch Function Setting mode).
The function of the footswitch cannot be changed.
Did you disable function change during normal operation in the footswitch function setting mode? (Refer to “Foot Switch Function Setting mode” on Page
page 11)
Specifications
(VMG-3/10/50 = VOX MINI GO 3/10/50)
Number of amp types: 11
Number of effects: 8
Number of program: 3 (VMG-50 only)
Number of rhythm patterns: 33
Tempo: 40-240BPM
Looper Recording lime: 0.25-45 sec. (VMG-10/50 only)
Tuner range: E1-E6 (41.2Hz — 1318.5Hz)
Input/Output jacks: INPUT, MIC IN, AUX IN, PHONES, FOOT SW (VMG-10/50 only)
Power amp output:
VMG-3 Maximum approx. 3W RAISIN ohms
VMG-10 Max approx. lOW RMS@16 ohms
VMG-50 Max approx. 50W RMS@4 ohms
Speaker:
VMG-3 5 inch 4 ohms
VMG-10 6.5 inch 16 ohms
VMG-50 8 inch 4 ohms
Power supply: Included AC adapter or USB mobile battery
Battery life with the 10000 mAh mobile battery used (approximate)
VMG-3: approx. 12 hours / VMG-10: approx. 6 hours / VMG-50: approx. 3 hours

Vox MINI GO 3 Specifications

General

Tempo range	40 - 240 bpm
Amplifier class	-
RMS rated power	3 W
Number of speakers	1
Speaker driver size	5 \
Audio output channels	- channels
Preset rhythm patterns	33
Sound effects quantity	8
Microphone in	Yes
Headphone connectivity	6.3 mm
Connectivity technology	Wired
Suitable for	Acoustic-electric guitar
Product color	Black
Volume control	Rotary
Power source type	AC, Battery

Weight and Dimensions

Depth	180 mm
Width	256 mm
Height	249 mm
Weight	3500 g