901302
SB M3x2.5
980210
P 2x10
#305323 50MM - STEEL
#305324 52MM - STEEL
#305325 50MM - ECS
#305326 52MM - ALU
#305327 52MM - ECS
#305328 50MM - ALU
05
4x
THREAD
LOCK
GRAPHITE GREASE
(HUDY #106210)
TL
TIP
For easy and comfortable
installation of the #305241
plastic caps use pliers as shown.
Longer drive shafts (52mm) make the car easier to drive because they
give more traction and better stability, mainly in chicanes. However, the
car will understeer more than with shorter (50mm) shafts which give a
lot of steering and impart aggression to the car. You may also combine
different lengths of shafts in front and rear (for example, using long shafts
in the rear and short shafts in the front) depending on track conditions.
Both left & right shafts should ALWAYS be the same length at one end of
the car (front or rear).
52mm shafts are recommended for carpet and big asphalt tracks
50mm shafts are recommended for small-medium tight asphalt tracks
The rear gear differential is made to fit 52mm drive shafts when using more than 2.5° rear toe-in and less than 2° camber.
If you want to use less than 2.5° toe-in and/or more than 2° camber (not recommended), you will need to remove a small
amount of material from the front of the plastic cap to allow it to fit into the gear diff.
DO NOT use the plastic caps with
composite solid axle included in the kits.
The new #305241 3.5mm plastic caps
are for use ONLY with GEAR diffs, ALU
ball diffs, or the XRAY Multi-Diff™.
ECS shafts are available optionally in both
50mm and 52mm lengths. The ECS drive
shafts were developed to decrease front wheel
vibration when racing with a solid front axle,
thus providing a much smoother and quieter
ride and increased steering.
BAG
5. FRONT & REAR TRANSMISSION
30 2252 COMPOSITE STEERING BLOCK - MEDIUM - V2 (OPTION)
30 2253 COMPOSITE STEERING BLOCK - HARD
30 2291 STEEL STEERING BUSHING (2+2)
30 2363 COMPOSITE C-HUB RIGHT - 4° DEG. - MEDIUM
30 2364 COMPOSITE C-HUB LEFT - 4° DEG. - MEDIUM
30 2373 COMPOSITE C-HUB RIGHT - 4° DEG. - HARD (OPTION)
30 2374 COMPOSITE C-HUB LEFT - 4° DEG. - HARD (OPTION)
30 2484 ANTI-ROLL BAR FRONT 1.4 MM
30 2652 BALL END 4.9MM WITH THREAD 4MM (2)
30 2655 BALL END 4.9MM WITH THREAD 10MM (2)
30 2665 COMPOSITE BALL JOINT 4.9MM - CLOSED WITH HOLE (4)
30 3122-K ALU SHIM 3x6x1.0MM - BLACK (10)
30 3123-K ALU SHIM 3x6x2.0MM - BLACK (10)
30 3129 COMPOSITE SET OF SHIMS (3x1MM; 1x2MM) (2)
30 3210 TURNBUCKLE M3 L/R 26 MM - SPRING STEEL™ (2) (OPTION)
30 3212 ALU ADJ. TURNBUCKLE M3 L/R 26 MM - SWISS 7075 T6 (2)
30 3352 UPRIGHT 0° OUTBOARD TOE-IN - MEDIUM
30 3353 UPRIGHT 1° OUTBOARD TOE-IN - RIGHT - HARD (OPTION)
30 3363 UPRIGHT 1° OUTBOARD TOE-IN - LEFT - HARD (OPTION)
30 3411 COMPOSITE ANTI-ROLL BAR HOLDERS - V2
30 3431-K ALU 5 MM BALL END - BLACK (2)
30 3454 BALL JOINT 5 MM - OPEN (4)
30 3482 ANTI-ROLL BAR REAR 1.2 MM
30 5231 DRIVE SHAFT COUPLING - HUDY SPRING STEEL™
30 5241 DRIVE SHAFT REPLACEMENT PLASTIC CAP 3.5 MM (4)
30 5323 DRIVE SHAFT 50MM - HUDY SPRING STEEL™ (OPTION)
30 5324 DRIVE SHAFT 52MM - HUDY SPRING STEEL™
30 5325 EQUALIZED CORNERING SPEED (ECS) DRIVE SHAFT 50MM (OPTION)
30 5326 ALU DRIVE SHAFT SWISS 7075 T6 - HARDCOATED - 52MM
30 5327 EQUALIZED CORNERING SPEED (ECS) DRIVE SHAFT 52MM (OPTION)
30 5328 ALU DRIVE SHAFT SWISS 7075 T6 - HARDCOATED - 50MM (OPTION)
30 5341 DRIVE AXLE - LIGHTWEIGHT - HUDY SPRING STEEL™
30 5350-K ALU WHEEL HUB - BLACK (2)
30 7221 FRONT ARM PIVOT PIN (2)
30 7321 REAR ARM PIVOT PIN (2)
30 7455 PIVOT BALL 4.9 MM DOUBLE BEVEL SHOULDERS (10)
90 1302 HEX SCREW SB M3x2.5 (10)
90 1303 HEX SCREW SB M3x3 (10)
90 1304 HEX SCREW SB M3x4 (10)
90 1308 HEX SCREW SB M3x8 (10)
90 2205 HEX SCREW SH M2x5 (10)
90 2310 HEX SCREW SH M3x10 (10)
90 2312 HEX SCREW SH M3x12 (10)
94 0510 HIGH-SPEED BALL-BEARING 5x10x4 RUBBER SEALED (2)
98 0210 PIN 2x10 (10)
902310
305324
902205
901304
303411
901303
901303
303431-K
303431-K
302484
303411
303454
303454
901308
901308
901308
303454
303454
305341
305341
940510
940510
980210
980210
902312
303129
307455
307221
901302
901302
305231
305231
302291
901304
302652
303122-K
902310
302655
303212
902205
305350-K
302655
302665
940510
302665
303212
307321
302652
303454
901308
303454
303431-K
303122-K
303431-K
901303
901303
303482
303352
303411
902310
901304
303411
901304
940510
303123-K
305241
305350-K
305326
303122-K
302253
303352
302364
302363
To Next Page
Loading...
Need help?
General
