To Next PageTo Next PageTo Previous PageTo Previous Page
What to do if my Zephyr Ventilation Hood turns on by itself?
If your Zephyr Ventilation Hood turns on by itself, it might be because a spotlight or kitchen lamp is shining directly onto the switch controls. These controls are light sensitive, and a direct light source may disrupt their function.
What to do if my Zephyr Ventilation Hood light works but the blower isn't turning?
If the light works, but the blower isn't turning on your Zephyr Ventilation Hood, several issues could be the reason. Start by checking the blower cable to ensure it's properly connected. Also, inspect the motor for any debris or obstructions that may be preventing it from turning. If those aren't the problem, the motor may be defective or seized, the capacitor might be damaged, or the switch board or control board could be defective, requiring you to change the defective part.
What to do if my Zephyr Typhoon AK2136CS is vibrating?
If your Zephyr Ventilation Hood is vibrating, it could be due to several reasons. First, check if the blower is securely in place and tighten it if necessary. A damaged blower wheel can also cause vibration, so consider replacing it. Lastly, ensure the hood itself is properly secured; check the installation.
What to do if my Zephyr Typhoon AK2136CS Ventilation Hood doesn’t work after installation?
If your Zephyr Ventilation Hood doesn’t work after installation, first ensure that the power source is turned ON by checking the circuit breaker and the unit's power. Then, verify that the power line and cable locking connector are properly connected. Also, check the wirings at the switch board and control board to ensure they are connected correctly. If the problem persists, the switch board or control board may be defective and need to be replaced.
Why is my Zephyr Ventilation Hood not venting properly?
There are several reasons why your Zephyr Ventilation Hood might not be venting properly. It could be due to using the wrong type of ducting, such as flexible ducting, which can significantly reduce airflow. Switching to solid rigid metal ducting can resolve this. Also, check if the hood is too high from the cooktop; adjust the distance to be between 24” and 32”. The wind from open windows or doors can also affect ventilation, so close them. Finally, ensure there are no blockages in the duct opening or ductwork.
Why are the lights not working on my Zephyr Ventilation Hood?
If the blower is working, but the lights are not on your Zephyr Ventilation Hood, it could be due to a few reasons. Check if the LED light connector is disconnected and connect it. If the connector is fine, the LED light might be defective and need to be replaced. Another possibility is that the switch board or control board is defective, requiring you to change it.
What to do if the safety grille is vibrating on my Zephyr Typhoon AK2136CS Ventilation Hood?
If the safety grille on your Zephyr Ventilation Hood is vibrating, it is likely that the safety grille is loose. To fix this, simply tighten the safety grille screw.
General| Color | stainless steel |
|---|---|
| Hood Type | under cabinet |
| Venting Type | ducted, external |
| Temperature Sensor | no |
| Number of Fan Speeds | 6 |
| CFM | 850 cubic feet per minute |
| Sones | 5 sones |
| Control Type | touch pad |
| Delay Start | yes |
| Interior Light | yes |
| Remote Control | no |
| Voltage | 120 volts |
Weight and Dimensions| Depth | 20 3/4 inches |
|---|---|
| Height | 7 7/8 inches |
| Width | 35 3/4 inches |
| Net Weight | 40.5 pounds |
General safety precautions and warnings to prevent injury and damage.
Guidelines for safe operation of the appliance, including blower precautions.
Details on power supply, wiring, grounding, and circuit protection.
Lists components included with the range hood unit.
Lists items required for installation but not included with the unit.
Worksheet to calculate total equivalent duct length for airflow efficiency.
Specifies recommended mounting height and ducting clearances for optimal performance.
Describes different methods for venting the range hood to the outdoors.
Technical dimensions and specifications for the AK21 model range hood.
Technical dimensions and specifications for the AK25 model range hood.
Technical dimensions and specifications for the AK65 model range hood.
Requirements and safety guidelines for connecting the range hood to the electrical system.
Information on using a cable locking connector for secure electrical connection.
Steps to prepare the hood for rectangular vertical ducting installation.
Steps to prepare the hood for rectangular horizontal ducting installation.
Detailed instructions and diagrams for physically installing the range hood under a cabinet.
Explains the controls and features of the AK21 model with capacitive touch interface.
Details the electronic touch controls and features of the AK25 model.
Describes the mechanical slide controls and features of the AK65 model.
Information on self-cleaning feature and cleaning frequency for the hood.
Guidelines for cleaning and maintaining the exterior surfaces of the hood.
Instructions for ordering replacement LumiLight LED modules and their removal.
Explains ACT™ for setting maximum CFM to meet local codes without makeup air kits.
