ABB 266HSH User Manual

2 266HSH MODBUS TRANSMITTER | PRESSURE/TEMPERATURE MULTIVARIABLE | OI/266HSHMT-EN REV. A
Table of contents
1 Introduction ........................................................... 3
1.1 Instruction manual structure ......................................... 3
1.2 Models covered by this manual ..................................... 3
1.3 Product description ........................................................ 3
2 Safety ...................................................................... 3
2.1 General safety information ............................................ 3
2.2 Improper use ....................................................................3
2.3 Technical limit values ...................................................... 3
2.4 Warranty provision .......................................................... 4
2.5 Use of instruction ...........................................................4
2.6 Operator liability .............................................................4
2.7 Qualified personnel .........................................................4
2.8 Returning devices ...........................................................4
2.9 Disposal ............................................................................ 4
2.10 Information on WEEE Directive 2012/19/UE (Waste
Electrical and Electronic Equipment) ................................4
2.11 Transport and storage .................................................. 4
2.12 Safety information for electrical installation ............ 4
2.13 Safety information for inspection & maintenance ...4
3 Transmitter overview ............................................ 5
3.1 Transmitter components overview ..............................5
3.2 Range & Span consideration .........................................6
4 Opening the box .................................................... 6
4.1 Identification ....................................................................6
4.2 Optional wired-on SST plate (I1) .................................. 7
4.3 Handling ........................................................................... 7
4.4 Storage ............................................................................. 7
5 Mounting ................................................................ 8
5.1 General ..............................................................................8
5.2 IP protection & designation ..........................................8
5.3 Mounting the transmitter ..............................................8
5.3.2 Hazardous area considerations ................................8
5.4 Pressure Equipment Directive (PED) (2014/68/EU) ..8
5.4.1 Devices with PS >200 ..................................................8
5.4.2 Devices with PS ≤200 bar ...........................................8
5.4.3 B6 & B7 Barrel housing bracket................................. 9
5.4.4 DIN Housing bracket details.....................................10
6 Setup .....................................................................11
6.1 Temperature measurement .........................................11
6.2 General information .....................................................11
6.3 Cable entries..................................................................11
6.4 Supply requirement......................................................11
6.5 Grounding ... ..................................................................12
6.6 Electical connection..................................................... 12
6.7 Electrical data for inputs and outputs...................... 12
6.8 Write protection............................................................15
6.8.1 Write protection activation..................................... . 15
6.9 Correcting the Lower Range Value ............................. 15
6.10 Correcting the zero shift ........................................... 15
6.11 Installing/Removing the LCD display ...................... 16
6.12 Securing the housing cover in flameproof areas ....16
7 Operation ..............................................................16
7.1 Local push button functionality (option R1).............. 16
7.2 Factory settings ............................................................. 16
7.3 Configuration types ...................................................... 16
7.4 Configuring the transmitter without an
integral LCD HMI ..................................................................17
7.5 LRV URV configuration ..................................................17
7.6 HMI as feedback of the local push
button operations ................................................................17
7.7 Correction of zero shift caused by installation
with PV Bias ...........................................................................17
7.8 LCD (L1 and LS option) activation considerations... 19
7.9 Through The Glass activation considerations .......... 19
7.10 Configuration of the pressure transmitter using
LCD HMI with keypad .......................................................... 20
7.11 Activation procedure for LCDs ...................................20
7.12 HMI menu structure ....................................................20
7.13 Damping (DAMPING) .................................................. 33
7.14 Configuration with teh PC/laptop or handheld
terminal ................................................................................34
7.15 Configuration with the graphical user interface
(DTM) - System requirements ..........................................35
7.16 Standard and Advanced HART: functionality ..........35
7.17 Standard HART software revision history ............... 36
8 Error messages .................................................... 36
8.1 LCD Display.....................................................................36
8.2 Error states and alarms ............................................... 37
9 Maintenance ......................................................... 40
9.1 Returns and removal .................................................... 40
9.2 Pressure transmitter sensor ...................................... 40
9.3 Removing/Installing the process flanges ................ 40
10 Hazardous Area considerations........................ 42
10.1 Ex Safety aspects and IP Protection (Europe) ........42
10.1.1 Entities for “L5” option ............................................46
10.2 Ex Safety aspects and IP Protection
(North America) ...................................................................46

ABB 266HSH Specifications

General

Brand	ABB
Model	266HSH
Category	Transmitter
Language	English