Operation Manual / A150-M56/66/57/67 - A155-M..
 Tables
© Copyright 2021 ABB. All rights reserved. HZTL4032_EN Revision Q January 2021
  Tables
Table1: Definition of pictograms ............................... 9
Table2: Personal protective equipment to be worn
at all times ...................................................................... 14
Table3: Personal protective equipment to be worn
specific to the respective task ................................... 14
Table4: Weight of complete turbocharger unit .... 29
Table5: Fitting the turbocharger, value X, L........... 35
Table6: Torque-controlled tightening of the pres-
sure screws .................................................................... 37
Table7: Lubricating oil pressure at oil inlet before
turbocharger ................................................................. 44
Table8: Lubricating oil temperature at the inlet... 45
Table9: Maximum lubricating oil temperature at the
outlet .............................................................................. 45
Table10: Tightening torque(86505)........................ 49
Table11: Expected replacement intervals ............... 55
Table12: Maintenance table....................................... 58
Table13: Parameters for wet cleaning of com-
pressor ............................................................................ 61
Table14: Turbine wet cleaning, recommended oper-
ating state ..................................................................... 64
Table15: Wet cleaning of turbines, parameters for 1-
nozzle cleaning.............................................................. 65
Table16: Wet cleaning of turbines, parameters for 6-
nozzle cleaning.............................................................. 66
Table17: Value table for soaking................................ 73
Table18: Tightening torque (81152 / 81154)............ 77
Table19: Malfunctions when starting – Delayed
start-up .......................................................................... 78
Table20: Malfunctions when starting – Vibrations 78
Table21: Malfunctions when starting – Rubbing of
rotating parts................................................................ 78
Table22: Malfunctions during operation – Lubricat-
ing oil pressure too low............................................... 79
Table23: Malfunctions during operation – Speed re-
duces............................................................................... 79
Table24: Malfunctions during operation – Speed in-
creases ........................................................................... 79
Table25: Malfunctions during operation – Exhaust
gas temperature too high .......................................... 80
Table26: Malfunctions during operation – Charge air
pressure too low............................................................ 80
Table27: Malfunctions during operation – Charge air
pressure too high .......................................................... 81
Table28: Malfunctions during operation – Engine
performance losses....................................................... 81
Table29: Malfunction – Turbocharger pumping..... 82
Table30: Malfunction – Sporadic surge blows........ 82
Table31: Malfunctions when stopping – Runout
noises............................................................................... 83
Table32: Malfunctions when stopping – Runout time
too short.......................................................................... 83
Table33: Malfunction of the speed measurement
system – No signal or poor signal amplitude .......... 84
Table34: Malfunction of the speed measurement
system – Measured speed too high........................... 84
Table35: Malfunction of the speed measurement
system – Measured speed too low............................. 84
Table36: Swivel lifting eyes......................................... 86
Table37: Press-off screws ........................................... 87
Table38: Dismantling screw ....................................... 87
Table39: Weights of assemblies................................ 92
Table40: Tightening torques...................................... 93
Table41: Tightening torques for insulation............. 94
Table42: 3 press-off screws...................................... 101
Table43: 6 press-off screws ..................................... 102
Table44: Tightening torque (90012-01) ................. 107
Table45: Permissible clearances A and B................ 112
Table46: Nozzle ring compression PD..................... 113
Table47: Tightening torque (90012-01)................... 116
Table48: Tightening torque (51007) ........................ 117
Table49: Tightening torque (79041) ........................ 118
Table50: Tightening torque (72011) ........................ 119
Table51: Permissible clearances N and R ............... 122
Table52: Tightening torque (51009) ....................... 125
Table53: Tightening torque (51009) ....................... 126
Table54: Tightening torque (72051)........................ 128
Page 193 / 194Page 193 / 194
To Next Page
Loading...
Need help?
General
