ABB COMMANDER 1900 Series User Manual

1
Section Page
1 INTRODUCTION ......................................................... 1
2 SETTING UP ............................................................... 2
2.1 Instrument Power-up ........................................ 2
2.1.1 Power-up Error Codes ........................ 3
2.2 Fitting the Chart................................................ 4
2.3 Fitting the Pen Capsule(s) ............................... 4
3 DISPLAYS & CONTROLS .......................................... 5
3.1 Displays and L.E.D. Indicators......................... 5
3.2 Use of Controls ................................................ 7
4 GENERAL OPERATION ............................................. 8
4.1 Input Error Messages ....................................... 9
5 CONTROL OPERATION........................................... 10
5.1 Operating Page Introduction .......................... 12
5.1.1 Set Point Tracking ............................ 12
5.1.2 Auto/Manual Transfer ....................... 12
5.1.3 Profile Control ................................... 12
5.1.4 Cascade Control ............................... 12
5.1.5 Heat/Cool Control ............................. 12
5.2 Operating Page Displays ............................... 13
5.3 Alarm Acknowledge Page .............................. 16
5.3.1 Alarm Indications .............................. 16
5.3.2 Acknowledging Alarms ..................... 16
5.3.3 Using the Alarm Acknowledge Page 16
5.4 Totals Page Displays ...................................... 17
5.5 Access to Configuration Levels ..................... 18
5.5.1 Security Code Page.......................... 18
5.6 Profile States Page ........................................ 19
5.7 Auto-tuning Introduction ................................. 20
5.7.1 Auto-tuning Page .............................. 21
5.8 Auto-tuning Diagnostic Messages ................. 24
5.9 Introduction to Standard Control .................... 25
5.9.1 Control Page (Standard Control)...... 30
5.10 Introduction to Heat/Cool Control .................. 31
5.10.1 Control Page (Heat/Cool Control) .... 32
5.10.2 Calculating the Crossover Value ...... 33
5.10.3 Calculating the Transition
Bandwidth Value ............................... 33
6 RECORD OPERATION ............................................. 34
6.1 Operating Page Displays ............................... 35
6.2 Alarm Acknowledge Page .............................. 36
6.2.1 Alarm Indications .............................. 36
6.2.2 Acknowledging Alarms ..................... 36
6.2.3 Using the Alarm Acknowledge Page 36
6.3 Totals Page Displays ...................................... 37
7 SIMPLE FAULT FINDING ......................................... 38
8 SPARES LIST ........................................................... 39
The COMMANDER 1900 series of documentation is shown in
Fig. 1.1. The
Standard Manuals, including the specification
sheet, are supplied with all instruments. The
Supplementary
Manuals supplied depend on the specification of the
instrument.
Part No.
IM/C1900–INS
INSTALLATION
Product Identification
Siting
Mounting
Electrical Connections
Installation Record
OPERATION
Setting Up
Error Messages
Operating Level
Simple Fault Finding
PROGRAMMING
Basic Config. Level
SPECIFICATION SHT.
Full Specification
Part No.
IM/C1900–OGC
Part No.
IM/C1900–PGC
Part No.
SS C1900
Flow Totalisation
Ramp/Soak Profile
Maths Functions
Timer Functions
Modbus (RTU)
Serial Adaptors
Serial Connections
Programming Pages
ASCII Tables
Part No.
IM/C1900–ADV
Part No.
IM/C1900–MOD
Control Config. Level
Displays & Controls
ADVANCED SOFTWARE
OPTIONS
Advanced Config. Level
A – Standard Manuals
B – Supplementary Manuals
Fig. 1.1 COMMANDER 1900 Documentation
CONTENTS 1 INTRODUCTION

ABB COMMANDER 1900 Series Specifications

General

Brand	ABB
Model	COMMANDER 1900 Series
Category	Voice Recorder
Language	English