EasyManuals Logo
Home>Amana>Microwave Oven>MC23MP

Amana MC23MP User Manual

Amana MC23MP
52 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #21 background imageLoading...
Page #21 background image
Service Test
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven and discharge capacitor
before servicing, unless testing requires power.
21 RS2240003 Rev. 0
STG
COOK
PREHEAT STANDBY
ITEM
POWER
CM
1
2
3
4
QTY
LEVEL
NOT READY
STG
COOK
PREHEAT STANDBY
ITEM
POWER
CM
1
2
3
4
QTY
LEVEL
NOT READY
STG
COOK
PREHEAT STANDBY
ITEM
POWER
CM
1
2
3
4
QTY
LEVEL
NOT READY
LMT
LMT
LMT
1
2
3
1 3 5 7 9
To Enter Service Test Mode, oven door must be closed.
NOTE: Unit must be in OFF condition
or
INITIAL power up mode.
Press
Display
Toggles Magnetron 2
(Top Front) ON/OFF.
Timer counts up to 62 seconds and unit shuts off.
Timer counts up to 62 seconds and unit shuts off.
STG
COOK
PREHEAT STANDBY
ITEM
POW ER
CM
1
2
3
4
QTY
LEVEL
NOT READY
LMT
Component Evaluation
STG
COOK
PREHEAT STANDBY
ITEM
POWER
CM
1
2
3
4
QTY
LEVEL
NOT READY
LMT
0=Deactivated
1=Activated
Displays actual Amperage,
will vary by model
Indicates
Service
Mode
If no Amperage, check for line
voltage at H.V. transformer
primary winding.
If no voltage, check:
Interlock switch (secondary)
Triac 3
H.V. board (relay K6 if 230 VAC,
K7 if 208 VAC, and triac 3
drive voltage T1 - G)
Wiring
If voltage is present, check:
H.V. components and wiring.
Then
NOTE: Pads will not beep when accessing Service Test Mode.
STG
COOK
PREHEAT STANDBY
ITEM
POWER
CM
1
2
3
4
QTY
LEVEL
NOT READY
LMT
STG
COO K
PREHEAT STANDBY
ITEM POWER
CM
1
2
3
4
QTY
LEVEL
NOT READ Y
LMT
Toggles Magnetron 3
(Bottom) ON/OFF.
Toggles Magnetron 1
(Top Rear) ON/OFF.
Timer counts up to 62 seconds and unit shuts off.
If no Amperage, check for line
voltage at H.V. transformer
primary winding.
If no voltage, check:
Interlock switch (secondary)
Triac 1
H.V. board (relay K8 if 230 VAC,
K9 if 208 VAC, and triac 1
drive voltage T1 - G)
Wiring
If no Amperage, check for line
voltage at H.V. transformer
primary winding.
If no voltage, check:
Interlock switch (secondary)
Triac 2
H.V. board (relay K4 if 208 VAC,
K5 if 230 VAC, and triac 2
drive voltage T1 - G)
Wiring
To EXIT Service Test Mode press STOP/RESET pad.
High Voltage System # 1
High Voltage System # 2
High Voltage System # 3
Displays actual Amperage,
will vary by model
Displays actual Amperage,
will vary by model
NOTE:
Not Applicable on Two Magnetron models:
DQ22HSI, RC17S, RC17SD2, and RC22S.
If voltage is present, check:
H.V. components and wiring.
If voltage is present, check:
H.V. components and wiring.
MC units
DQ22HSI
MENU
WDYRC2
Hidden
Pad
RC units
MENU
1
2
3
4
BREAKFAST
REG MENU
PREP
MISC
Hidden
Pad
Hidden
Pad
Hidden
Pad
QUANTITY
Press Hidden Pad
as indicated above
on touch panels.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Amana MC23MP and is the answer not in the manual?

Amana MC23MP Specifications

General IconGeneral
BrandAmana
ModelMC23MP
CategoryMicrowave Oven
LanguageEnglish

Related product manuals