EN | 15
D9412G/D7412G | Operation & Installation Guide |
Bosch Security Systems | 10/03 | 43488E
2.4.5 Keyswitch
Any of the eight available areas can be armed/disarmed
with maintained or momentary closure devices such as
keyswitches. Point programming determines loop
responses and the area a keyswitch controls.
2.4.6 Access Control
The D9412G can control eight access doors (each
requiring the optional D9210B Wiegand Control
Interface Module) with up to 996 uniquely identified
cards/tokens. The D7412G can control two access doors
with up to 396 uniquely identified cards/tokens. Access
can be granted from a Wiegand style access control
device (card reader) connected to the D9210B Access
Control Interface Module. Access can also be granted
from a “request to enter” or a “request to exit” input, or
from a command center.
The access control features of the D9412G/D7412G can
deny access during armed periods. It can also grant
access only to certain authorized users depending on
whether the area is master armed, perimeter armed, or
disarmed. The alarm system can be programmed to
automatically disarm when designated authorized users
are granted access.
2.4.7 Event Memory
The system uses event memory to store events for each
area. The events for an area can be viewed at a D1255
Command Center assigned to the area. The panel clears
the events for an area from event memory and starts
storing new events when the area is master armed.
2.4.8 Event Log
The system stores 500 to 1000 events and event
modifiers from all areas in its event log. Event modifiers
add information about an event to the log. Some events
are always followed by a modifier. For example, the
system adds at least two items to the log each time an
area is armed or disarmed, the open (or close) event and
an event modifier showing the previous arming state.
All events and their modifiers can be stored even if the
panel does not send a report for them. The log can be
viewed at a command center, printed locally using the
D9131A Parallel Printer Interface Module and a parallel
printer, or uploaded to the Remote Account Manager
(RAM) IV.
See the appendix in the command center’s User’s Guide
for a listing of log events and event modifiers.
2.4.9 EMI and Lightning Transient Protection
The D9412G/D7412G Control Panels maintain the
Bosch Security Systems’ level of quality and field
dependability. Their design significantly reduces
electromagnetic interference and malfunction generally
caused by lightning.
2.4.10 Programming
Use the Bosch Security Systems D5200 Programmer or
the Remote Programming Software (RPS) to program
the D9412G/D7412G Control Panels. Refer to the
D9412G/D7412G Program Entry Guide for programming
options.
2.4.11 Other Features
D9412G/D7412G Control Panels have many
programmable features. Some of the features are listed
below. Complete details on all features are in the
D9412G/D7412G Program Entry Guide.
• Supervision of AC (primary power), battery
(secondary power), ZONEX, and SDI buses,
Central Processing Unit (CPU), a maximum of
three printers, and two telephone lines
• Automatic System Test Reports
• Remote access for programming, diagnostics, and
log uploads using the RPS
• Fire alarm verification
• Programmable alarm output
• Programmable relay output using the D8129
OctoRelay Module
• Opening and closing windows
• Skeds (scheduled events)
2.4.12 Control Panel Assembly
The D9412G/D7412G Control Panel is shipped pre-
assembled from the factory with the following parts:
Literature Pack
• D9412G/D7412G/D7212G Installation and
Troubleshooting Quick Reference Guide
• D9412G/D7412G Program Record Sheet
• 9000/9000G Series Technical Service Note: UL
Smoke Detector Compatibility
• 7000/9000 Series Point Chart Label
Assembly
• PC board
• Faceplate shield
• Mounting skirt
• One #6 x 1/4-in. screw
2.0 Overview
To Next Page
Loading...
Need help?
General
