Bose FreeSpace IZA 190-HZ User Manual

Page 26 Installation and Operation English
Setup and Operation pro.Bose.com
Setup – Rear-panel controls
FreeSpace IZA 190-HZ
FRONT MIC
MIX
FRNT MIC
DUCK
t
q
r
e
w
FreeSpace IZA 250-LZ
q
t
r
w
e
. LOKHÚDQØLNCDØ#(/ØRVHSBGDR
• PAGE/MIC NORMAL – BYPASS MASTER
Determines if page input source will follow the master level output or can be set at a fixed output level to ensure
announcements are heard. When set to BYPASS MASTER use the respective input gain controls to adjust the volume
level of each microphone.
• OUTPUT MONO – OUTPUT STEREO
Determines if stereo input sources will be output in mono or stereo via loudspeaker connectors and AUX OUT RCA
connectors. Using this switch in a mono position will help provide sufficient gain for single-input devices. Mono switch
position will also sum stereo inputs for loudspeaker applications where stereo is not desired.
Note: On the IZA 250-LZ amplifier, OUTPUT 1 is the left channel and OUTPUT 2 is the right channel when set to OUTPUT
STEREO. On the IZA 190-HZ, the left channel is routed to the loudspeaker output when set to OUTPUT STEREO.
• FRONT MIC MIX – FRONT MIC DUCK
Determines if front-panel microphone input will be mixed in with music source or if the music output level will be
automatically lowered (“ducked”) when someone speaks into microphone.
• AUX OUT EQ – AUX OUT FLAT
Determines if AUX OUT will have selected loudspeaker EQ preset applied to it or not. Allows for optimization of
FreeSpace DS 16 and DS 40 loudspeakers when used with additional zone amplifiers.
3 Loudspeaker EQ preset switch
Provides loudspeaker equalization presets designed to optimize the performance of Bose FreeSpace DS 16 or DS 40
loudspeakers. A high-pass filter (HPF) setting is also available for use with any passive loudspeakers. The high-pass
filter is set at 60 Hz for the IZA 190-HZ and at 40 Hz for the IZA 250-LZ.
The selected EQ preset (HPF, DS 16, DS 40) can be sent to an additional zone amplifier via AUX OUT if “AUX OUT EQ”
is selected with the corresponding mode DIP switch.
$ Page input GAIN control
Allows for fine-tuning page input levels. If the front-panel INPUT CLIP indicator is red, reduce the input gain.
The adjustment range is 0 dB to +50 dB.
/ Line input GAIN control
Allows for fine-tuning of INPUT A/B levels. If the front-panel INPUT CLIP indicator is red, reduce the input gain.
The adjustment range is –20 dB to +20 dB.
1 Output TRIM control
Allows for attenuating individual loudspeaker outputs relative to the Master Level. The adjustment range is –20 dB to
0 dB. This feature is helpful when one output is powering loudspeakers that need to be set at a lower volume level than
loudspeakers on other outputs – including the outputs of an additional zone amplifier.

Bose FreeSpace IZA 190-HZ Specifications

General

Amplifier class	D
RMS rated power	90 W
Channels quantity	1 channels
Audio output channels	- channels
Peak power per channel	- W
Signal-to-Noise Ratio (SNR)	- dB
Total Harmonic Distortion (THD)	1 %
XLR in	Yes
Line inputs (RCA)	2
Line outputs (RCA)	1
Speakers connectivity type	RCA
Product color	Silver
Rack capacity	1U
Volume control	Rotary
Connectivity technology	Wired
AC input voltage	230 V
AC input frequency	50 - 60 Hz
Power protection features	Overheating, Short circuit
Power consumption (typical)	15 W
Package weight	4100 g

Weight and Dimensions

Depth	310 mm
Width	214 mm
Height	45 mm
Weight	3200 g