Carel c.pCO sistema User Manual

42
ENG
c.pCO sistema +0300057EN rel. 1.2 - 29.05.2017
Acquire/ release commands
These commands are used by a controller to acquire / release a terminal.
Procedure:
1. Press Alarm and ENTER together to enter the system menu. Select
“Settings”
INFORMATION
SETTINGS
APPLICATION
UPGRADE
LOGGER
DIAGNOSTICS
2. Select pLAN Settings
PASSWORD
USB SETTINGS
PLAN SETTINGS
CLOCK SETTINGS
TCP/IP SETTINGS
3. The following screen is shown, where the acquire/release
commands can be activated.
pLan pCO Addr: 1
Release Term: No
Acquire Term: No
Update config: No/Yes
Key
pLan pCO addr. Address of c.pCO controller currently connected to the
terminal
Release terminal Release command
Acquire terminal Acquire command
Update congu-
ration
Conrm update
Command virtualisation
Whenever a pGD terminal is connected to a c.pCO, the pGD terminal
displays the corresponding user interface. The command is sent from
the terminal, however it is the controller that executes the operation to
release or acquire the terminal.
Example 1
A: the release command on terminal 21 releases c.pCO 3 from terminal
21, and this is then assigned to c.pCO 1;
B: the release command on terminal 21 releases c.pCO 1 from terminal 21,
and this is then assigned to c.pCO 2.
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SM
B
d
r
a
c
suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SM
B
d
r
a
c
suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
Term 21:
Release term
AB
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SM
B
d
r
a
c
suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
Term 21:
Release term
Example 2
A: the release command on terminal 22 releases c.pCO 3 from terminal
21, and this is then assigned to c.pCO 1;
B: the release command on terminal 22 releases c.pCO 3 from terminal 22,
and this is then assigned to c.pCO 1.
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
Term 22:
Release term
AB
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
Term 22:
Release term
Example 3
A: the acquire command on terminal 22 acquires c.pCO 1 on terminal 21,
and this is thus assigned to c.pCO 1;
B: the acquire command on terminal 22 has no eect, as c.pCO 1 has
already acquired all the terminals
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SM
B
d
r
a
c
suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SM
B
d
r
a
c
suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
Term 22:
Release term
AB
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SM
B
d
r
a
c
suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
Term 22:
Release term
6.6 Uploading/updating the software
It is possible to load/update the application software of the c.pCO
controllers family with the following methods:
• Update from computer by using c.factory (via USB or Ethernet
connection
• Update via USB ash drive
• Update with le transfer via FTP (see par. FTP commands)
• Update via tERA cloud service
The c.factory software is part of the “c.suite”, but it can be also installed
individually, downloading it from http://ksa.carel.com under “Software &
Support”->“c.suite”.
Update from computer using c.factory
On all c.pCO family controllers, the application program can be uploaded
by using the c.factory software, with direct connection to the controller
via USB cable or Ethernet network. To upload the application program,
proceed as follows:
a) Update from computer using c.factory via Ethernet connection:
Congure the computer and the c.pCO controller so that they belong to
the same LAN (see paragraph 9.2).
1. Open c.factory and select the application program le compiled in
c.strategy tool (“.otr” le extension). The tool will list the congurations
dened in c.design. Select the conguration to be loaded on the
controller and click “next”.
Fig. 6.f

Carel c.pCO sistema Specifications

General

Brand	Carel
Model	c.pCO sistema
Category	Controller
Language	English