Cisco ASR 1002 Replacing

SUMMARY STEPS
1. Before inserting a SIP, make sure that the chassis is grounded.
2. To insert the SIP, carefully align the edges of the SIP between the upper and lower edges of the router
slot.
3. Carefully slide the SIP into the router slot until the SIP makes contact with the backplane.
4. Tighten the locking thumbscrews on both sides of the SIP.
5. Connect all cables to each SPA.
DETAILED STEPS
Step 1 Before inserting a SIP, make sure that the chassis is grounded.
Step 2 To insert the SIP, carefully align the edges of the SIP between the upper and lower edges of the router slot.
Step 3 Carefully slide the SIP into the router slot until the SIP makes contact with the backplane.
Step 4 Tighten the locking thumbscrews on both sides of the SIP.
Step 5 Connect all cables to each SPA.
Removing a Shared Port Adapter from a SIP
To remove a shared port adapter (SPA), follow these steps.
SUMMARY STEPS
1. Attach an ESD wrist strap between you and an unpainted chassis surface.
2. Shut down the interface so that there is no traffic running through the shared port adapter when it is
removed.
3. Disconnect all cables from the shared port adapter.
4. Unscrew the captive installation screws on either side of the SPA.
5. Grasp the handles and pull the SPA from the SIP.
DETAILED STEPS
Step 1 Attach an ESD wrist strap between you and an unpainted chassis surface.
Step 2 Shut down the interface so that there is no traffic running through the shared port adapter when it is removed.
Removing a shared port adapter while traffic is flowing through the ports can cause system disruption.
Caution
Refer to the following example to shut down the interface FastEthernet0/1/0 on the 8-Port Fast Ethernet Shared Port
Adapter (SPA-8X1FE-TX-V2).
a) At the router# prompt, type:configure terminal and press Enter. The global configuration mode prompt Router
(config)# appears.
b) At the router (config)# prompt, type:interface FastEthernet0/1/0 and press Enter. The interface configuration mode
prompt Router(config-if)# appears.
c) At the router (config-if)# prompt, type:shutdown and press Enter. This disables the interface FastEthernet0/1/0.
d) At the router(config-if)# prompt, type:end and press Enter. The privileged EXEC mode prompt Router# appears.
Removing and Replacing FRUs from the Cisco ASR 1000 Series Routers
56
Removing and Replacing FRUs from the Cisco ASR 1000 Series Routers
Removing a Shared Port Adapter from a SIP

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g