Cisco ASR 1002 Replacing

Step 3 Disconnect all cables from the shared port adapter.
Step 4 Unscrew the captive installation screws on either side of the SPA.
Step 5 Grasp the handles and pull the SPA from the SIP.
What to do next
You have completed the removal procedure for the Cisco ASR 1000 Series SPA.
Replacing a Shared Port Adapter in a SIP
To replace a shared port adapter in a SIP module, follow these steps:
SUMMARY STEPS
1. To insert the SPA in the SIP, locate the guide rails inside the SIP that hold the SPA in place. They are at
the top left and top right of the SPA slot and are recessed about an inch.
2. Carefully slide the SPA all the way in the SIP until the SPA is firmly seated in the SPA interface connector.
When fully seated, the SPA might be slightly behind the SIP faceplate.
3. After the SPA is properly seated, fasten the SPA in place with the captive installation screws on either
side of the SPA.
DETAILED STEPS
Step 1 To insert the SPA in the SIP, locate the guide rails inside the SIP that hold the SPA in place. They are at the top left and
top right of the SPA slot and are recessed about an inch.
Step 2 Carefully slide the SPA all the way in the SIP until the SPA is firmly seated in the SPA interface connector. When fully
seated, the SPA might be slightly behind the SIP faceplate.
Step 3 After the SPA is properly seated, fasten the SPA in place with the captive installation screws on either side of the SPA.
Removing and Replacing the Cisco ASR 1006 Router Power
Supplies
The Cisco ASR 1006 Router contains power supplies that are field replaceable units. This section contains
the following topics:
Removing and Replacing a AC Power Supply in Cisco ASR 1006 Router
This section provides information about removing and replacing an AC power supply in the Cisco ASR 1006
Router.
Removing and Replacing FRUs from the Cisco ASR 1000 Series Routers
57
Removing and Replacing FRUs from the Cisco ASR 1000 Series Routers
Replacing a Shared Port Adapter in a SIP

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g